GE HEALTHCARE
DIRECTION 2307224-100, REVISION 6DISCOVERY LS SYSTEM SERVICE MANUAL
Page 28 List of Figures
Figure 6-84: CT Plug ............................................................................................................................................ 170
Figure 6-85: CT Detent/Flag Assembly ................................................................................................................ 171
Figure 6-86: PET Detent/Flag Assembly ............................................................................................................. 172
Figure 6-87: Adjust PET Detent for Recorded Distance Between Scan Planes .................................................. 173
Figure 6-88: PET Detent Adjuster, P/N 2332092 ................................................................................................. 173
Figure 6-89: PET Detent Adjuster Fastened into Place ....................................................................................... 174
Figure 6-90: Check Relationship between Roller Arm and Pin Out of Detent ..................................................... 175
Figure 6-91: Check the Relationship between the Roller Arm and Pin on the Detent ......................................... 175
Figure 6-92: Check Relationship between Roller Arm and Pin in the Detent ...................................................... 176
Figure 6-93: Fasten Optical Sensor with One Screw ........................................................................................... 177
Figure 6-94: Swing the Optical Sensor into Place ............................................................................................... 177
Figure 6-95: Align the Optical Sensor to the Flag ................................................................................................ 178
Figure 6-96: Mark the Flag ................................................................................................................................... 179
Figure 6-97: Center the Flag ................................................................................................................................ 179
Figure 6-98: Table Latch Assembly ..................................................................................................................... 180
Figure 6-99: Adjust the Set Screw for 90 Degrees .............................................................................................. 180
Figure 6-100: Fasten Service Latch to Table Rail with Three Sets of M5 Hardware ............................................. 181
Figure 6-101: Adjust CT Position Assembly to Clear Table Latch Arm ................................................................. 182
Figure 6-102: Correctly Adjusted Position Latch Arm ............................................................................................ 182
Figure 6-103: Reposition the Solenoid ................................................................................................................... 183
Figure 6-104: Check Latch Clearance in "Energized" Position .............................................................................. 183
Figure 6-105: Adjust the Solenoid Spring .............................................................................................................. 184
Figure 6-106: Latch in Service Position ................................................................................................................. 184
Figure 6-107: New Characterization Bracket ......................................................................................................... 185
Figure 6-108: Install Three Top Cover Brackets .................................................................................................... 186
Figure 6-109: Install Top Cover Bracket, P/N 233371 ........................................................................................... 187
Figure 6-110: Install Ten Cosmetic Cradle Caps, P/N 46-221523P10 .................................................................. 188
Figure 6-111: Automated Table Covers ................................................................................................................. 189
Figure 6-112: Secondary Base Covers .................................................................................................................. 190
Figure 6-113: Assemble the Roller Cover Guides ................................................................................................. 191
Figure 6-114: Secondary Base Side Rail Slot Locations ....................................................................................... 192
Figure 6-115: Fasten Roller Cover Guides into Place ........................................................................................... 192
Figure 6-116: Install the Roller Cover Bracket ....................................................................................................... 193
Figure 6-117: Roller Cover Bracket, P/N 2332803 ................................................................................................ 193
Figure 6-118: Align Cover Bracket with Cover Guide ............................................................................................ 194
Figure 6-119: Reposition the Ground Bus Bar ....................................................................................................... 194
Figure 6-120: Canister Bracket Assembly (with and without Canister) ...........................................................
....... 195
Figure 6-121: Attach Drip Trough, P/N 2333438 ................................................................................................... 196
Figure 6-122: Roller Canister in Place (P/N 2331848) ........................................................................................... 197
Figure 6-123: Inset Idler Roller (P/N 2331418) into Slot in Table Base ................................................................. 198
Figure 6-124: M4 Hardware Holds Idler Roller in Place ......................................................................................... 198
Figure 6-125: Align Idler Roller to Roller Cover Guides ......................................................................................... 199
Figure 6-126: Use a Screwdriver to Pull Cover Out of Canister ............................................................................ 199
Figure 6-127: Check Cover Clearances ................................................................................................................. 200
Figure 6-128: Side Cover - Back View to Show Guide Pins .................................................................................. 201
Figure 6-129: Side Covers - Exploded View .......................................................................................................... 202
Figure 6-130: Secondary Base with Side Covers and Roller Cover Open ............................................................ 203
Figure 6-131: Interface Cover ................................................................................................................................ 203
Figure 6-132: Square the Table Top Cover ........................................................................................................... 204
Figure 6-133: Top Cover Fastened into Place ....................................................................................................... 204
Figure 6-134: Table Top Cap Assembly (P/N 2320161) ........................................................................................ 205
Figure 6-135: Attach the Back Cover Brackets to the Secondary Base ................................................................ 206
Figure 6-136: Back Cap (P/N2320164) Rear View w/ Profile Bracket ................................................................... 207
Figure 6-137: Attach Back Cap to Motor Base ...................................................................................................... 208
Figure 6-138: ME 1.5 Table Block Diagram ........................................................................................................... 209
Figure 6-139: Gantry Keypad ................................................................................................................................. 210
To Next Page
Loading...
