Omron RX2 Series - Page 895

C - 47
Appendices C Table of Parameters
High-function General-purpose Inverter RX2 Series User’s Manual
C-3 Parameter List
C
Code
Codes that
can be
changed
during
operation
Name Data range
Initial
value
Note
CC-01 ○ Output terminal [11] function
See <List of output terminal functions> on page C-49
001
CC-02 ○ Output terminal [12] function 002
CC-03 ○ Output terminal [13] function 003
CC-04 ○ Output terminal [14] function 007
CC-05 ○ Output terminal [15] function 035
CC-06 ○ Output terminal [16] function 000
CC-07 ○ Output terminal [AL] function 017
CC-11 ○ Output terminal [11] function
00 (Normally open)/
01 (Normally closed)
00
CC-12 ○ Output terminal [12] function 00
CC-13 ○ Output terminal [13] function 00
CC-14 ○ Output terminal [14] function 00
CC-15 ○ Output terminal [15] function 00
CC-16 ○ Output terminal [16] function 00
CC-17 ○ Output terminal [AL] function 01
CC-20 ○ Output terminal [11] on-delay time 0.00 to 100.00 (s) 0.00
CC-21 ○ Output terminal [11] off-delay time 0.00 to 100.00 (s) 0.00
CC-22 ○ Output terminal [12] on-delay time 0.00 to 100.00 (s) 0.00
CC-23 ○ Output terminal [12] off-delay time 0.00 to 100.00 (s) 0.00
CC-24 ○ Output terminal [13] on-delay time 0.00 to 100.00 (s) 0.00
CC-25 ○ Output terminal [13] off-delay time 0.00 to 100.00 (s) 0.00
CC-26 ○ Output terminal [14] on-delay time 0.00 to 100.00 (s) 0.00
CC-27 ○ Output terminal [14] off-delay time 0.00 to 100.00 (s) 0.00
CC-28 ○ Output terminal [15] on-delay time 0.00 to 100.00 (s) 0.00
CC-29 ○ Output terminal [15] off-delay time 0.00 to 100.00 (s) 0.00
CC-30 ○ Output terminal [16] on-delay time 0.00 to 100.00 (s) 0.00
CC-31 ○ Output terminal [16] off-delay time 0.00 to 100.00 (s) 0.00
CC-32 ○ Output terminal [AL] on-delay time 0.00 to 100.00 (s) 0.00
CC-33 ○ Output terminal [AL] off-delay time 0.00 to 100.00 (s) 0.00
CC-40 ○
Logical calculation target 1 selection
of LOG1
See <List of output terminal functions> on page C-49
062: LOG1 to 068: LOG7 cannnot be selected.
000
CC-41 ○
Logical calculation target 2 selection
of LOG1
See <List of output terminal functions> on page C-49
062: LOG1 to 068: LOG7 cannnot be selected.
000
CC-42 ○
Logical calculation symbol selection
of LOG1
00 (AND)/01 (OR)/02 (XOR) 00
CC-43 ○
Logical calculation target 1 selection
of LOG2
See <List of output terminal functions> on page C-49
062: LOG1 to 068: LOG7 cannnot be selected.
000
CC-44 ○
Logical calculation target 2 selection
of LOG2
See <List of output terminal functions> on page C-49
062: LOG1 to 068: LOG7 cannnot be selected.
000
CC-45 ○
Logical calculation symbol selection
of LOG2
00 (AND)/01 (OR)/02 (XOR) 00
CC-46 ○
Logical calculation target 1 selection
of LOG3
See <List of output terminal functions> on page C-49
062: LOG1 to 068: LOG7 cannnot be selected.
000
CC-47 ○
Logical calculation target 2 selection
of LOG3
See <List of output terminal functions> on page C-49
062: LOG1 to 068: LOG7 cannnot be selected.
000
CC-48 ○
Logical calculation symbol selection
of LOG3
00 (AND)/01 (OR)/02 (XOR) 00
CC-49 ○
Logical calculation target 1 selection
of LOG4
See <List of output terminal functions> on page C-49
062: LOG1 to 068: LOG7 cannnot be selected.
000
CC-50 ○
Logical calculation target 2 selection
of LOG4
See <List of output terminal functions> on page C-49
062: LOG1 to 068: LOG7 cannnot be selected.
000
CC-51 ○
Logical calculation symbol selection
of LOG4
00 (AND)/01 (OR)/02 (XOR) 00
CC-52 ○
Logical calculation target 1 selection
of LOG5
See <List of output terminal functions> on page C-49
062: LOG1 to 068: LOG7 cannnot be selected.
000
CC-53 ○
Logical calculation target 2 selection
o
f LOG5
See <List of
output terminal functions> on page C-49
062: LOG1 to 068: LOG7 cannnot be selected.
000