ANTILOCK BRAKE SYSTEM 4F–23
DAEWOO M-150 BL2
intrusion exists, replace the wheel speed sensor har-
ness. If replacing a wheel speed sensor harness, in-
spect the sensor terminals. If you find evidence of
corrosion or water intrusion, replace the wheel speed
sensor. Refer to “Front Wheel Speed Sensor” in this
section.
Important: Wheel speed sensor intermittent malfunc-
tions may be difficult to locate. Take care not to disturb
any electrical connections before performing an indi-
cated step of this table. That will ensure that an intermit-
tent connection will not be corrected before the source
of the malfunction is found.
DTC 0356 – Left Front Wheel Speed Sensor Circuit Intermittent Shorted
Step
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Action
Value(s)
Yes
No
ÑÑ
ÑÑ
ÑÑ
ÑÑ
ÑÑ
ÑÑ
1
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
1. Turn the ignition switch to OFF.
2. Disconnect the EBCM harness connector from
the EBCM.
3. Use a digital voltmeter (DVM) to measure the
resistance between terminals 14 and 25 of
connector on the EBCM harness.
Is the resistance within the specified value?
ÑÑÑ
ÑÑÑ
ÑÑÑ
ÑÑÑ
ÑÑÑ
ÑÑÑ
1.0 k to
1.5 k
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
Go to Step 4
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
Go to Step 2
ÑÑ
ÑÑ
ÑÑ
ÑÑ
2
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
1. Disconnect the harness from the left front wheel
speed sensor.
2. Use a DVM to measure the resistance between
terminals 1 and 2 of the left front wheel speed
sensor connector.
Is the resistance within the specified value?
ÑÑÑ
ÑÑÑ
ÑÑÑ
ÑÑÑ
1.0 k to
1.5 k
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
Go to Step 4
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
Go to Step 3
ÑÑ
3
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Replace the wheel speed sensor.
Is the repair complete?
ÑÑÑ
–
ÑÑÑÑÑ
System OK
ÑÑÑÑ
–
ÑÑ
ÑÑ
4
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Use a DVM to measure the resistance between
ground and terminal 14 of the EBCM connector.
Does the DVM show the specified value?
ÑÑÑ
ÑÑÑ
1
ÑÑÑÑÑ
ÑÑÑÑÑ
Go to Step 6
ÑÑÑÑ
ÑÑÑÑ
Go to Step 5
ÑÑ
5
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Repair the short to ground in circuit DK BLU.
Is the repair complete?
ÑÑÑ
–
ÑÑÑÑÑ
System OK
ÑÑÑÑ
–
ÑÑ
6
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Use a DVM to measure the resistance between
ground and terminal 25 of the EBCM connector.
Does the DVM show the specified value?
ÑÑÑ
1
ÑÑÑÑÑ
Go to Step 8
ÑÑÑÑ
Go to Step 7
ÑÑ
7
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Repair the short to ground in circuit YEL.
Is the repair complete?
ÑÑÑ
–
ÑÑÑÑÑ
System OK
ÑÑÑÑ
–
ÑÑ
ÑÑ
ÑÑ
8
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
1. Turn the ignition switch to ON.
2. Use a DVM to measure the voltage between
ground and terminal 14 of the EBCM connector.
Is the voltage within the specified value?
ÑÑÑ
ÑÑÑ
ÑÑÑ
0 v
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
Go to Step 10
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
Go to Step 9
ÑÑ
9
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Repair the short to voltage in circuit DK BLU.
Is the repair complete?
ÑÑÑ
–
ÑÑÑÑÑ
System OK
ÑÑÑÑ
–
ÑÑ
10
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Use a DVM to measure the resistance between
ground and terminal 25 of the EBCM connector.
Does the voltage within the specified value?
ÑÑÑ
0 v
ÑÑÑÑÑ
Go to Step 12
ÑÑÑÑ
Go to Step 11
ÑÑ
11
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Repair the short to voltage in circuit YEL.
Is the repair complete?
ÑÑÑ
–
ÑÑÑÑÑ
System OK
ÑÑÑÑ
–
ÑÑ
12
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Replace the EBCM.
Is the repair complete?
ÑÑÑ
–
ÑÑÑÑÑ
System OK
ÑÑÑÑ
–
To Next Page
Loading...
