4F–50 ANTILOCK BRAKE SYSTEM
DAEWOO M-150 BL2
DTC 0506 – Right Rear Wheel Speed Sensor Circuit Intermittent Shorted (Cont’d)
Step
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Action
Value(s)
Yes
No
ÑÑ
ÑÑ
11
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Repair the short to ground between terminal 10 of
the connector C202 and terminal 1 of the right rear
wheel speed sensor harness connector.
Is the repair complete?
ÑÑÑ
ÑÑÑ
–
ÑÑÑÑÑ
ÑÑÑÑÑ
System OK
ÑÑÑÑ
ÑÑÑÑ
–
ÑÑ
ÑÑ
ÑÑ
12
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
1. Turn the ignition switch to ON.
2. Use a DVM to measure the voltage between
ground and terminal 9 of the EBCM connector.
Is the voltage within the specified value?
ÑÑÑ
ÑÑÑ
ÑÑÑ
0 v
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
Go to Step 14
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
Go to Step 13
ÑÑ
ÑÑ
13
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Repair the short to voltage between terminal 2 of the
connector C202 and terminal 9 of the EBCM con-
nector.
Is the repair complete?
ÑÑÑ
ÑÑÑ
–
ÑÑÑÑÑ
ÑÑÑÑÑ
System OK
ÑÑÑÑ
ÑÑÑÑ
–
ÑÑ
ÑÑ
ÑÑ
14
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
1. Turn the ignition switch to ON.
2. Use a DVM to measure the voltage between
ground and terminal 2 of the connector C202.
Is the voltage within the specified value?
ÑÑÑ
ÑÑÑ
ÑÑÑ
0 v
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
Go to Step 16
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
Go to Step 15
ÑÑ
ÑÑ
15
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Repair the short to voltage between terminal 2 of the
connector C202 and terminal 2 of the right rear
wheel speed sensor harness connector.
Is the repair complete?
ÑÑÑ
ÑÑÑ
–
ÑÑÑÑÑ
ÑÑÑÑÑ
System OK
ÑÑÑÑ
ÑÑÑÑ
–
ÑÑ
ÑÑ
ÑÑ
16
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
1. Turn the ignition switch to ON.
2. Use a DVM to measure the voltage between
terminal 10 of the connector C202 and terminal
10 of the EBCM connector.
Is the voltage within the specified value?
ÑÑÑ
ÑÑÑ
ÑÑÑ
0 v
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
Go to Step 18
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
Go to Step 17
ÑÑ
ÑÑ
ÑÑ
17
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Repair the short to voltage between terminal 10 of
the connector C202 and terminal 10 of the EBCM
connector.
Is the repair complete?
ÑÑÑ
ÑÑÑ
ÑÑÑ
–
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
System OK
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
–
ÑÑ
ÑÑ
18
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
1. Turn the ignition switch to ON.
2. Use a DVM to measure the voltage between
ground and terminal 10 of the connector C202.
Is the voltage within the specified value?
ÑÑÑ
ÑÑÑ
0 v
ÑÑÑÑÑ
ÑÑÑÑÑ
Go to Step 20
ÑÑÑÑ
ÑÑÑÑ
Go to Step 19
ÑÑ
ÑÑ
ÑÑ
19
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Repair the short to voltage between terminal 10 of
the connector C202 and terminal 1 of the right rear
wheel speed sensor harness connector.
Is the repair complete?
ÑÑÑ
ÑÑÑ
ÑÑÑ
–
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
System OK
ÑÑÑÑ
ÑÑÑÑ
ÑÑÑÑ
–
ÑÑ
20
ÑÑÑÑÑÑÑÑÑÑÑÑÑÑÑ
Replace the EBCM.
Is the repair complete?
ÑÑÑ
–
ÑÑÑÑÑ
System OK
ÑÑÑÑ
–