7A–8 HEATING AND VENTILATION SYSTEM
DAEWOO M-150 BL2
Insufficient Heating or Defrosting (Cont’d)
Step
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Action
Value(s)
Yes
No
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
ÁÁ
23
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
1. Back flush the heater core.
2. Drain the cooling system.
3. Replace the coolant.
4. Warm the engine to an average operating
temperature.
5. Feel the heater inlet hose and the heater outlet
hose.
Is the heater inlet hose hot and the heater outlet
hose warm?
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
System OK
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Go to Step 24
ÁÁ
24
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Replace the heater core.
Is the repair complete?
ÁÁÁ
–
ÁÁÁÁÁ
System OK
ÁÁÁÁ
–
ÁÁ
ÁÁ
ÁÁ
25
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Recheck the system using the “Control
Settings/Correct Results” tests. Refer to ‘‘Improper
Air Delivery or No Mode Shift” in this section.
Is the repair complete?
ÁÁÁ
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
System OK
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Go to Step 26
ÁÁ
ÁÁ
26
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Check for airflow from the defroster or the vent
outlets.
Is there high airflow from the defroster or the vent
outlets?
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to Step 27
ÁÁÁÁ
ÁÁÁÁ
Go to Step 28
ÁÁ
ÁÁ
27
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Adjust the heater door at the floor and the vent door
to get the proper airflow.
Is the repair complete?
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
System OK
ÁÁÁÁ
ÁÁÁÁ
–
ÁÁ
28
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Switch the mode knob to defrost.
Is the defroster airflow OK?
ÁÁÁ
–
ÁÁÁÁÁ
Go to Step 29
ÁÁÁÁ
Go to Step 30
ÁÁ
ÁÁ
ÁÁ
29
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
1. Remove the heater outlet and check for
obstructions.
2. Remove any obstructions in the heater outlet.
Is the repair complete?
ÁÁÁ
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
System OK
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
–
ÁÁ
30
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Check for airflow change at various blower speeds.
Does the blower speed increase as the control is
turned from 1 to 4?
ÁÁÁ
–
ÁÁÁÁÁ
Go to Step 31
ÁÁÁÁ
Go to ‘‘Blower
Electrical’’
ÁÁ
ÁÁ
31
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Check for obstructions in the system at the blower
inlet.
Are there any obstructions?
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to Step 32
ÁÁÁÁ
ÁÁÁÁ
Go to Step 33
ÁÁ
ÁÁ
32
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Remove the obstructions in the system at the blower
inlet.
Is the repair complete?
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
System OK
ÁÁÁÁ
ÁÁÁÁ
–
ÁÁ
ÁÁ
ÁÁ
33
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
1. Set the blower on 4.
2. Rotate the temperature control from full hot to full
cold.
3. Listen for an airflow change.
Does the airflow change?
ÁÁÁ
ÁÁÁ
ÁÁÁ
–
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
Go to Step 34
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Go to Step 35