Endress+Hauser Proline Promag 300 - Page 263

Proline Promag 300 Modbus RS485 Index
Endress+Hauser 263
Decimal places 4 (Parameter) .................. 24
Default gateway (Parameter) ..................158
Define access code (Parameter) ................. 40
Define access code (Wizard) ................... 40
Density (Parameter) ......................... 47
Density source (Parameter) .................... 85
Density unit (Parameter) ...................... 60
Device alarm simulation (Parameter) ............ 210
Device ID (Parameter) ....................... 155
Device information (Submenu) ................ 181
Device name (Parameter) .................... 183
Device reset (Parameter) ...................... 42
Device revision (Parameter) ...................155
Device tag (Parameter) ...................... 182
DHCP client (Parameter) ..................... 157
Diagnostic behavior (Submenu) ................. 32
Diagnostic event category (Parameter) ...........211
Diagnostic event simulation (Parameter) ......... 211
Diagnostic handling (Submenu) ................. 31
Diagnostic list (Submenu) .................... 174
Diagnostics (Submenu) ...................... 171
Diagnostics 1 (Parameter) .................... 175
Diagnostics 2 (Parameter) .................... 175
Diagnostics 3 (Parameter) .................... 176
Diagnostics 4 (Parameter) .................... 177
Diagnostics 5 (Parameter) .................... 178
Direct access
0/4 mA value
Current input 1 to n (1606–1 to n) ........ 100
Current output 1 to n (0367–1 to n) ....... 108
0% bargraph value 1 (0123) .................18
0% bargraph value 3 (0124) .................22
2.4 GHz WLAN channel (2704) ............. 164
20 mA value
Current input 1 to n (1607–1 to n) ........ 101
Current output 1 to n (0372–1 to n) ....... 109
100% bargraph value 1 (0125) ...............19
100% bargraph value 3 (0126) ...............22
Access status (0005) ...................... 13
Activate SW option (0029) ..................42
Active level
Status input 1 to n (1351–1 to n) ..........104
Actual diagnostics (0691) ..................172
Alarm delay (0651) ....................... 31
Alteration code (2762) .....................98
Apply I/O configuration (3907) .............. 98
Assign behavior of diagnostic no. 043 (0650) .... 33
Assign behavior of diagnostic no. 302 (0739) .... 33
Assign behavior of diagnostic no. 376 (0645) .... 34
Assign behavior of diagnostic no. 377 (0777) .... 34
Assign behavior of diagnostic no. 441 (0657) .... 34
Assign behavior of diagnostic no. 442 (0658) .... 35
Assign behavior of diagnostic no. 443 (0659) .... 35
Assign behavior of diagnostic no. 444 (0740) .... 35
Assign behavior of diagnostic no. 531 (0741) .... 36
Assign behavior of diagnostic no. 543 (0643) .... 36
Assign behavior of diagnostic no. 832 (0681) .... 37
Assign behavior of diagnostic no. 833 (0682) .... 37
Assign behavior of diagnostic no. 834 (0700) .... 37
Assign behavior of diagnostic no. 835 (0702) .... 38
Assign behavior of diagnostic no. 937 (0743) .... 38
Assign behavior of diagnostic no. 938 (0642) .... 38
Assign behavior of diagnostic no. 961 (0736) .... 39
Assign behavior of diagnostic no. 962 (0745) .... 39
Assign channel 1 (0851) .................. 192
Assign channel 2 (0852) .................. 192
Assign channel 3 (0853) .................. 193
Assign channel 4 (0854) .................. 193
Assign current output 1 to n (0359–1 to n) .....106
Assign diagnostic behavior
Pulse/frequency/switch output 1 to n (0482–
1 to n) ............................. 132
Relay output 1 to n (0806–1 to n) ......... 141
Assign flow direction check
Pulse/frequency/switch output 1 to n (0484–
1 to n) ............................. 136
Relay output 1 to n (0808–1 to n) ......... 140
Assign frequency output
Pulse/frequency/switch output 1 to n (0478–
1 to n) ............................. 126
Assign limit
Pulse/frequency/switch output 1 to n (0483–
1 to n) ............................. 133
Relay output 1 to n (0807–1 to n) ......... 140
Assign process variable
Totalizer 1 to n (0914–1 to n) ............ 167
Assign process variable (1837) ...............76
Assign pulse output 1 (0982–1) ............. 146
Assign pulse output 1 to n (0460–1 to n) ...... 122
Assign simulation process variable (1810) ..... 202
Assign SSID name (2708) ..................164
Assign status
Pulse/frequency/switch output 1 to n (0485–
1 to n) ............................. 136
Relay output 1 to n (0805–1 to n) ......... 141
Assign status input
Status input 1 to n (1352–1 to n) ..........103
Backlight (0111) ......................... 28
Backup state (2759) .......................30
Baudrate (7111) ........................ 151
Bootloader revision
I/O module 2 (0073) ............... 188, 190
I/O module 3 (0073) ............... 188, 190
I/O module 4 (0073) ............... 188, 190
Bootloader revision (0073) ......... 185, 186, 191
Build no. software
I/O module 2 (0079) ............... 188, 189
I/O module 3 (0079) ............... 188, 189
I/O module 4 (0079) ............... 188, 189
Build no. software (0079) ..........185, 186, 190
Bus address (7112) ...................... 150
Bus termination (7155) ................... 154
Byte order (7113) ....................... 152
Calibration factor (6522) ................... 96
Clear logging data (0855) ..................194
Comparison result (2760) ...................30
Conductivity (1850) ....................... 46
Conductivity calibration factor (6718) ..........96