R&S SMA100B - Source:ils Subsystem

Remote control commands
R&S
®
SMA100B
603User Manual 1178.3834.02 ─ 09
[:SOURce<hw>]:ADF:COMid[:STATe] <State>
Enables/disables the COM/ID signal.
Parameters:
<State> 1 | ON | 0 | OFF
*RST: 0
Example: See Example "Configure and generate a ADF signal"
on page 594.
Manual operation: See "COM/ID State" on page 168
14.16.2.4 SOURce:ILS subsystem
Option: R&S SMAB-K25
The SOURce:BB:ILS subsystem contains all commands for configuring the ILS signal.
Characteristics which are valid for all modulations and the LF output are configured in
the SOURce:LFOutput subsystem. The signal is output at the LF connector.
Commands
[:SOURce<hw>]:ILS:TYPE..............................................................................................604
[:SOURce<hw>]:ILS[:GS|GSLope]:DDM:COUPling........................................................... 605
[:SOURce<hw>]:ILS[:GS|GSLope]:DDM:CURRent............................................................605
[:SOURce<hw>]:ILS[:GS|GSLope]:DDM:DIRection............................................................605
[:SOURce<hw>]:ILS[:GS|GSLope]:DDM:LOGarithmic........................................................606
[:SOURce<hw>]:ILS[:GS|GSLope]:DDM:PCT................................................................... 606
[:SOURce<hw>]:ILS[:GS|GSLope]:DDM:POLarity............................................................. 606
[:SOURce<hw>]:ILS[:GS|GSLope]:DDM:STEP................................................................. 607
[:SOURce<hw>]:ILS[:GS|GSLope]:DDM[:DEPTh]..............................................................607
[:SOURce<hw>]:ILS[:GS|GSLope]:FREQuency................................................................ 607
[:SOURce<hw>]:ILS[:GS|GSLope]:FREQuency:MODE......................................................608
[:SOURce<hw>]:ILS[:GS|GSLope]:FREQuency:SYNChronize[:STATe]................................ 608
[:SOURce<hw>]:ILS[:GS|GSLope]:ICAO:CHANnel............................................................608
[:SOURce<hw>]:ILS[:GS|GSLope]:LLOBe[:FREQuency]....................................................609
[:SOURce<hw>]:ILS[:GS|GSLope]:MODE........................................................................ 609
[:SOURce<hw>]:ILS[:GS|GSLope]:PHASe....................................................................... 609
[:SOURce<hw>]:ILS:GS|GSLope:PRESet........................................................................ 610
[:SOURce<hw>]:ILS[:GS|GSLope]:SDM...........................................................................610
[:SOURce<hw>]:ILS[:GS|GSLope]:SOURce..................................................................... 610
[:SOURce<hw>]:ILS[:GS|GSLope]:ULOBe[:FREQuency]................................................... 611
[:SOURce<hw>]:ILS:LOCalizer:COMid:CODE...................................................................611
[:SOURce<hw>]:ILS:LOCalizer:COMid:DASH................................................................... 611
[:SOURce<hw>]:ILS:LOCalizer:COMid:DEPTh................................................................. 612
[:SOURce<hw>]:ILS:LOCalizer:COMid:DOT..................................................................... 612
[:SOURce<hw>]:ILS:LOCalizer:COMid:FREQuency.......................................................... 612
[:SOURce<hw>]:ILS:LOCalizer:COMid:LETTer................................................................. 613
[:SOURce<hw>]:ILS:LOCalizer:COMid:PERiod.................................................................613
[:SOURce<hw>]:ILS:LOCalizer:COMid:SYMBol................................................................ 613
SOURce subsystem