Command groups
Table 2-21: Bus commands (cont.)
Command Description
BUS:B<x>:I2C:CLOCk:SOUrce Sets or queries the I2C clock (SCLK) source for the specified bus.
BUS:B<x>:I2C:CLOCk:THReshold Sets or queries the I2C Clock (SCLK) source threshold for the specified bus.
BUS:B<x>:I2C:D ATa:SOUrc e Sets or queries the I2C data (SDA) source for the specified bus.
BUS:B<x>:I2C:D ATa:THR eshold Sets or queries the I2C Data (SDA) source threshold for the specified bus.
BUS:B<x>:I2C:RWINADDR Determines whether decoded I2C slave addresses are pure seven-bit values,
or have the R/W* combined with them.
BUS:B<x>:LABel:COLor Sets or queries the color of the specified bus label.
BUS:B<x>:LABel:FONT:BOLD Sets or queries the bold s tate of the specified bus label.
BUS:B<x>:LABel:FONT:ITALic Sets or queries the italic state of the specified bus label.
BUS:B<x>:LABel:FONT:SIZE Sets or queries the font size of the specified bus label.
BUS:B<x>:LABel:FONT:TYPE Sets or queries the font type of the specified bus label, such as Arial or Times
New Roman.
BUS:B<x>:LABel:FONT:UNDERline Sets or queries the underline state of the specified bus label.
BUS:B<x>:LABel:name Sets or queries the waveform label for the specified bus.
BUS:B<x>:LABel:XPOS Sets or queries the x-position of the specified bus' label.
BUS:B<x>:LABel:YPOS Sets or queries the y-position of the specified bus' label.
BUS:B<x>:LIN:BITRate Sets or queries the LIN bus bit rate.
BUS:B<x>:LIN:ID FORmat Sets or queries LIN bus id format.
BUS:B<x>:LIN:PO Larity Sets or queries the LIN bus polarity.
BUS:B<x>:LIN:SAMPLEpoint Specifies the point to sample during each bit period, as a percent, for the
specified LIN bus.
BUS:B<x>:LIN:SOUrce Sets or queries sets the LIN bus source.
BUS:B<x>:LIN:SOUrce:THReshold Sets or queries the LIN source threshold for the specified bus.
BUS:B<x>:LIN:STANDard Sets or queries the LIN bus standard.
BUS:B<x>:LIN:BITRate:CUSTom Sets or queries LIN custom bit rate for the specified bus.
BUS:B<x>:MIL1553B:SOUrce Sets or queries the source for the specified MIL-STD-1553 bus.
BUS:B<x>:MIL1553B:THRESHold Sets or queries the MIL-STD-1553 upper threshold for the specified bus.
BUS:B<x>:MIL1553B:LOWTHRESHold Sets or queries the MIL-STD-1553 lower threshold for the specified bus.
BUS:B<x>:MIL1553B:POLarity Sets or queries the source polarity for the specified MIL-STD-1553 bus.
BUS:B<x>:MIL1553B:RESPonsetime:MINimum Sets or queries the minimum response time to a valid command issued for the
specified MIL-STD-1553 bus.
BUS:B<x>:MIL1553B:RESPonsetime:MAXimum Sets or queries the maximum response time to a valid command issued for the
specified MIL-STD-1553 bus.
BUS:B<x>:PARallel:ALLTHResholds Sets or queries the threshold for all sources for the parallel bus.
BUS:B<x>:PARallel:ALLTHResholds:APPly Sets all of the data s ource thresholds to the value of the allMRefs parameter for
the parallel bus.
BUS:B<x>:PARallel:BIT<n>SOUrce Sets or queries the specified bit source for specified parallel bus.
BUS:B<x>:PARallel:BIT<n>SOUrce:THReshold Sets or queries the specified bit source threshold for the specified parallel bus.
2-16 MSO54, MSO56, MSO58, MSO58LP Programmer
To Next Page