Omron Q2V Series - Page 220

7.3 List of Fault, Minor Fault, Alarm, and Error Codes
220 SIEPCYEUOQ2V01A Q2V Technical Manual
Display (Hex.) Name ALM LED Type Ref.
oPE07 Analog Input Selection Error Flashing Parameter Setting Errors 248
oPE08 Parameter Selection Error Flashing Parameter Setting Errors 249
oPE09 PID Control Selection Fault Flashing Parameter Setting Errors 249
oPE10 V/f Data Setting Error Flashing Parameter Setting Errors 250
oPE11 Carrier Frequency Setting Error Flashing Parameter Setting Errors 250
oPE13 Pulse Monitor Selection Error Flashing Parameter Setting Errors 250
oPE16 Energy Saving Constants Error Flashing Parameter Setting Errors 250
oPE33 Digital Output Selection Error Flashing Parameter Setting Errors 250
oPr (001E) Keypad Connection Fault Illuminated Fault 233
oS (0010) Overspeed Flashing Alarm 244
oS (0018) Overspeed Illuminated Fault 244
ov (0002) Overvoltage Flashing Alarm 244
ov (0008) Overvoltage Illuminated Fault 233
PASS Modbus Communication Test Flashing Not an alarm. 245
PE1 (0047)
PE2 (0048)
PLC Faults Illuminated Fault 234
PF (0047) Input Phase Loss Flashing Alarm 245
PF (001B) Input Phase Loss Illuminated Fault 234
PWEr Q2pack Password Mismatch - Backup Function Error 255
qAL1 (0049) Q2pack Alarm Flashing Alarm 240
qAL2 (004A) Q2pack Alarm 2 Flashing Alarm 240
qAL3 (004B) Q2pack Alarm 3 Flashing Alarm 240
qFL1 (004A) EEPROM Memory Q2pack Data Error Illuminated Fault 225
qFL2 (004B) Q2pack Fault 2 Illuminated Fault 225
qFL3 (004C) Q2pack Fault 3 Illuminated Fault 225
qFL (0049) Q2pack Fault Illuminated Fault 225
rdEr Error Reading Data - Backup Function Error 255
rF (004E) Braking Resistor Fault Illuminated Fault 234
rH (0010) Braking Resistor Overheat Illuminated Fault 235
rr (000F) Dynamic Braking Transistor Fault Illuminated Fault 235
rUn (001B) Motor Switch during Run Flashing Alarm 245
SC (0005) Short Circuit/IGBT Failure Illuminated Fault 235
SCF (040F) Safety Circuit Fault Illuminated Fault 235
SE (0020) Modbus Test Mode Error Flashing Alarm 245
SEr (003B) Speed Search Retries Exceeded Illuminated Fault 235
SToF (003B) Safe Torque OFF Flashing Alarm 245
STPo (0037) Motor Step-Out Detected Illuminated Fault 236
TiM (0089) Keypad Time Not Set Flashing Alarm 246
TiM (0401) Keypad Time Not Set Illuminated Fault 236
TrPC (0042) IGBT Maintenance Time (90%) Flashing Alarm 246
UL3 (001E) Undertorque Detection 1 Flashing Alarm 246
UL3 (0029) Undertorque Detection 1 Illuminated Fault 236
UL4 (001F) Undertorque Detection 2 Flashing Alarm 246
UL4 (002A) Undertorque Detection 2 Illuminated Fault 236
UL5 (003E) Mechanical Weakening Detection 2 Flashing Alarm 246
UL5 (0045) Mechanical Weakening Detection 2 Illuminated Fault 236
Uv (0001) DC Bus Undervoltage Flashing Alarm 246