Tektronix MSO56 User Manual

Command groups
Table 2-31: Measurement commands (cont.)
Command
Description
MEASUrement:MEAS<x>:REFLevels<x>:
PERCent:TYPE
This command specifies or queries the reference level percent type for the
measurement.
MEASUrement:MEAS<x>:REFMode This command sets or queries the reference level mode for the measurement.
MEASUrement:MEAS<x>:REFVoltage This command sets or queries the reference voltage value for the measurement.
MEASUrement:MEAS<x>:RESUlts:ALLAcqs:
MAXimum?
This command is identical to that described in the DPOJet p rogrammer manual.
MEASUrement:MEAS<x>:RESUlts:ALLAcqs:
MEAN?
This command is identical to that described in the DPOJet p rogrammer manual.
MEASUrement:MEAS<x>:RESUlts:ALLAcqs:
MINimum?
This command is identical to that described in the DPOJet p rogrammer manual.
MEASUrement:MEAS<x>:RESUlts:ALLAcqs:
PK2PK?
This command is identical to that described in the DPOJet p rogrammer manual.
MEASUrement:MEAS<x>:RESUlts:ALLAcqs:
POPUlation?
This command is identical to that described in the DPOJet p rogrammer manual.
MEASUrement:MEAS<x>:RESUlts:ALLAcqs:
STDDev?
This command is identical to that described in the DPOJet p rogrammer manual.
MEASUrement:MEAS<x>:RESUlts:
CURRentacq:MAXimum?
This query-only command returns the maximum value found for the specified
measurement since the last statistical reset.
MEASUrement:MEAS<x>:RESUlts:
CURRentacq:MEAN?
This query-only command returns the mean value for the measurement for the current
acquisition.
MEASUrement:MEAS<x>:RESUlts:
CURRentacq:MINimum?
This query-only command returns the minimum value found for the specified
measurement since the last statistical reset.
MEASUrement:MEAS<x>:RESUlts:
CURRentacq:PK2PK?
This query-only command returns the peak-to-peak value for the specified
measurement for the current acquisition.
MEASUrement:MEAS<x>:RESUlts:
CURRentacq:POPUlation?
This query-only command returns the population for the specified measurement for
the current acquisition.
MEASUrement:MEAS<x>:RESUlts:
CURRentacq:STDDev?
This query-only command returns the standard deviation for the specified
measurement for all acquisitions accumulated since statistics were last reset.
MEASUrement:MEAS<x>:SIGNALType This command sets or queries the signal type of source 1 for the m easurement.
MEASUrement:MEAS<x>:SOUrce<x> Sets or queries the measurement source.
MEASUrement:MEAS<x>:SSC:NOMinalfreq This command sets or queries the user-de fined frequency for the measurement when
the measurement type is SSC.
MEASUrement:MEAS<x>:SSC:NOMinalfreq:
SELECTIONtype
This command sets or queries the frequency detection type for the measurement
when the measurement type is SSC.
MEASUrement:MEAS<x>:TOEdge This command sets or queries the 'to edge' type for the measurement.
MEASUrement:MEAS<x>:
TOEDGESEARCHDIRect
This command sets or queries the 'to edge' search direction for the measurement.
MEASUrement:MEAS<x>:TRANSition This command sets or queries the transition edges flag for the measurement.
MSO54, MSO56, MSO58, MSO58LP Programmer 2-49

Tektronix MSO56 Specifications

General

Brand	Tektronix
Model	MSO56
Category	Test Equipment
Language	English