Tektronix MSO56 User Manual

Command groups
Table 2-37: Search and Mark commands (cont.)
Command
Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:
AUDio:DATa:TDMVALue
Sets or queries the binary data string for the single or low data word to be used
when searching on an TDM audio bus signal
SEARCH:SEARCH<x>:TRIGger:A:BUS:
AUDio:DATa:VALue
Sets or queries the binary data string for the single or low data word to be used
when searching on an audio bus signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
AUDio:DATa:WORD
Sets or queries the alignment of the data (left, right or either) to be used when
searching on a non-TDM type audio bus signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:CONDition
Sets or queries the CAN bus trigger condition.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:DATa:DIRection
Sets the CAN search type.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:DATa:OFFSet
Sets or queries the data offset value, in bytes, to use when searching on the CAN
data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:DATa:QUALifier
Sets or queries the CAN bus trigger data qualifier.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:DATa:SIZe
Sets or queries the CAN bus trigger data size.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:DATa:VALue
Sets or queries the binary data value to be used when searching on a CAN bus
signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:ERRType
Sets or queries the type of error condition for a CAN bus to search on.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:FD:BRSBit
Sets or queries the value of the bit rate switch bit (BRS bit) for a CAN bus to
search on.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:FD:ESIBit
Sets or queries the value of the error state indicator bit (ESI bit) for a CAN bus
to search on.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:FRAMEtype
Sets or queries CAN bus trigger frame type.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:IDentifier:MODe
Sets or queries the CAN bus trigger identifier mode.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
CAN:IDentifier:VALue
Sets or queries C AN bus trigger identifier value.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
ETHERnet:CONDition
Specifies a field or condition within an Ethernet frame to s earch on.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
ETHERnet:DATa:HIVALue
Sets or queries the binary data value to be used when searching on an Ethernet
bus signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
ETHERnet:DATa:OFFSet
Specifies the data offset value, in bytes, to use when searching on the Ethernet
data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
ETHERnet:DATa:QUALifier
Sets the qualifier to be used when searching on an Ethernet bus signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
ETHERnet:DATa:SIZe
Specifies the number of contiguous TCP/IPv4/MAC client bytes to use when
searching on the Ethernet data field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
ETHERnet:DATa:VALue
Specifies the binary value to use when searching on the Ethernet data field.
MSO54, MSO56, MSO58, MSO58LP Programmer 2-65

Tektronix MSO56 Specifications

General

Brand	Tektronix
Model	MSO56
Category	Test Equipment
Language	English