YOKOGAWA DLM4000 Series User Manual

Index-4
IM DLM4038-02EN
PolygonZone ........................................................................ 2-72
POSITION knob...................................................................... 2-2
power supply analysis type and power measurement .......... 14-1
PRINT Built-in menu ............................................................. 16-3
printer errors ......................................................................... 20-3
printers, roll paper for ........................................................... 16-1
printer test............................................................................. 20-7
PRINT File menu .................................................................. 16-5
print mode, built-in printer ..................................................... 16-3
print mode, network printer ................................................... 16-4
PRINT Multi menu ................................................................ 16-7
PRINT Network menu ........................................................... 16-4
probe, setting .......................................................................... 1-3
probe setup, power measurement ...................................... 14-10
probe setup, power supply analysis ..................................... 14-2
protection, turning on and off .............................................. 17-20
PSI5 Airbag, analyzing and searching ................................ 12-31
PSI5 Airbag trigger ............................................................... 2-42
PTYPE mode, CXPI bus search ......................................... 12-21
pulse width search ...............................................................11-10
pulse width trigger .................................................................2-11
Q
Page
qualification, edge search with conditions .............................11-5
qualification, edge trigger with conditions ............................... 2-8
R
Page
range type............................................................................. 2-69
RectZone .............................................................................. 2-69
reference setting, angle cursor ............................................... 8-5
reference setup....................................................................... 8-5
reference time, pulse width search ......................................11-12
reference time, pulse width trigger ....................................... 2-13
reference time, state condition trigger .................................. 2-16
reference time, state width search.......................................11-16
reference waveforms, loading waveform data into ............. 17-10
ref levels ................................................................................. 9-5
replay .................................................................................... 15-4
RESET key .................................................................................v
roll paper, handling ............................................................... 16-1
rotary count............................................................................. 6-7
RUN/STOP key ...................................................................... 3-2
R/W bit inclusion, I2C ......................................................... 12-48
R/W bit inclusion, trigger....................................................... 2-51
S
Page
safe operating area analysis................................................. 14-5
sampling mode ....................................................................... 3-1
save destination.................................................................... 17-2
save mode ............................................................................ 16-5
scaling .................................................................................... 6-8
SCL source ................................................................ 2-49, 12-47
screen capture, saving ......................................................... 17-7
SDA source................................................................ 2-50, 12-47
SDTV (480/60p).................................................................... 2-61
SEARCH CAN FD menu ...................................................... 12-9
search, CAN FD serial bus signal....................................... 12-12
SEARCH CAN menu ............................................................ 12-5
search, CAN serial bus signal .............................................. 12-8
search condition, edge ..........................................................11-2
search condition, edge with conditions ..................................11-5
search condition, history waveforms .................................... 15-5
search condition, pulse width ..............................................11-11
search conditions, CXPI bus .............................................. 12-22
SEARCH CXPI menu ......................................................... 12-17
search, CXPI serial bus signal............................................ 12-20
SEARCH Edge menu ............................................................11-1
SEARCH Edge Qualified menu .............................................11-4
search, FlexRay bus ............................................................. 12-4
SEARCH FlexRay menu ...................................................... 12-1
SEARCH I2C menu ............................................................ 12-45
search, I2C serial bus signal .............................................. 12-50
SEARCH LIN menu ............................................................ 12-13
search, LIN serial bus signal .............................................. 12-16
SEARCH PAI5 Airbag menu ............................................... 12-31
search, PSI5 ....................................................................... 12-36
SEARCH Pulse Width menu ...............................................11-10
SEARCH SENT menu ........................................................ 12-24
search, SENT signal ........................................................... 12-30
search skipping......................................................................11-3
SEARCH SPI menu ............................................................ 12-51
search, SPI serial bus signal .............................................. 12-56
SEARCH State menu ............................................................11-7
SEARCH State Width menu ................................................11-13
SEARCH UART menu ........................................................ 12-39
search, UART signal ........................................................... 12-44
search, user-defined bus signal.......................................... 12-60
SEARCH User Define menu............................................... 12-57
self-tests ............................................................................... 20-6
SENT signals, analyzing and searching ............................. 12-24
SENT trigger ......................................................................... 2-34
serial bus analysis results, saving ........................................ 17-8
serial bus, CAN bus, analyzing and searching ..................... 12-6
serial bus, CAN FD bus, analyzing and searching ............. 12-10
serial bus, CXPI bus, analyzing and searching .................. 12-18
serial bus, FlexRay bus, analyzing and searching ............... 12-2
serial bus, I2C bus, analyzing and searching ..................... 12-46
serial bus, LIN bus, analyzing and searching ..................... 12-14
serial bus, PSI5, analyzing and searching.......................... 12-32
serial bus, SENT, analyzing and searching ........................ 12-25
serial bus, SPI bus, analyzing and searching ..................... 12-52
serial bus, UART, analyzing and searching ........................ 12-40
serial bus, user-defined bus, analyzing and searching....... 12-58
serial number ........................................................................ 20-8
SET key ......................................................................................v
set/reset .............................................................................. 17-20
setting errors......................................................................... 20-5
setting information, including ....................................... 16-5, 17-6
setup data, loading ..............................................................17-11
setup data, saving ................................................................ 17-5
setup information, viewing .................................................... 19-3
SHIFT key ..................................................................................iv
SINGLE key ............................................................................ 3-2
single mode ..................................................................... 2-1, 3-2
skip mode ..............................................................................11-3
Slow CH ID/Data mode, SENT trigger .................................. 2-39
smoothing ............................................................................... 6-4
snapshot ................................................................................. 4-4
snapshot waveforms, loading ............................................. 17-13
snapshot waveforms, saving ................................................ 17-8
SNTP .................................................................................. 18-10
SNTP server ....................................................................... 18-10
SOA ...................................................................................... 14-5
SOF mode, CAN bus trigger................................................. 2-21
SOF mode, CAN FD bus trigger ........................................... 2-26
SOF mode, CXPI bus search ............................................. 12-20
soft keyboard test ................................................................. 20-7
SPI bus trigger ...................................................................... 2-54
SPI serial bus signals, analyzing and searching ................ 12-51
start bit mode ........................................................................ 2-44
start bit mode, PSI5 search ................................................ 12-36
start byte ............................................................................... 2-53
Start Byte mode .................................................................... 2-53
state condition .......................................................................11-8
state condition, state condition trigger .................................... 2-9
state condition, state width ..................................................11-14
Index

YOKOGAWA DLM4000 Series Specifications

General

Brand	YOKOGAWA
Model	DLM4000 Series
Category	Test Equipment
Language	English