Chapter 53 Provisioning User Interfaces
OLT2406 User’s Guide
411
8 Configure VLAN flow settings for the subscriber port on the remote ONT and check the settings.
• The subscriber User Network Interface (UNI) port at slot 6, port 1, ONT 101, card 1, card port 1.
• QoS queue: configure QoS settings to apply to a specific traffic class.
• tc: traffic class 0-7 to which to apply this queue, 1 in this example.
• priority: This is reserved for future development since the Zyxel ONTs do not support this QoS feature
now. Yet, it’s mandatory to enter a value. We use 0 in this example.
• weight: This is reserved for future development since the Zyxel ONTs do not support this QoS feature
now. Yet, it’s mandatory to enter a value. We use 0 in this example.
• usbwprofname: upstream bandwidth profile to use for the traffic class, voice in this example.
• dsbwprofname: downstream bandwidth profile to use for the traffic class, voice in this example.
• dsoption: Set whether to apply the downstream rate limit function to the OLT (olt) or the ONT (ont).
• bwsharegroupid: bandwidth group ID 1-40 on this ONT to put the QoS queues into. This example
uses the 1, the bandwidth group you configured in step 5 on page 408.
• VLAN settings:
• VLAN: UNI VLAN of traffic (10 in this example) to which to apply this command's QoS ingress profile
and AES encryption settings.
• Network: the Network Node Interface (NNI) VID, 10 in this example. Use a number different from the
UNI VLAN to apply VLAN translation.
• ingprof: the QoS ingress profile to apply to the VLAN’s traffic, voip in this example.
• AES encryption: enabled or disabled (Disabled in this example).
• Active: on or off (On in this example).
OLT2406# config
OLT2406(config)# vlan 10
OLT2406(config-vlan)# fixed ge-6-1
OLT2406(config-vlan)# fixed msc-1-1
OLT2406(config-vlan)# exit
OLT2406# config
OLT2406(config)# remote uniport uniport-6-1-101-1-1
OLT2406(config-remote-uniport)# no inactive
OLT2406(config-remote-uniport)# queue tc 1 priority 0 weight 0 usbwprofname voice
dsbwprofname voice dsoption olt bwsharegroupid 1
OLT2406(config-remote-uniport)# vlan 10 network 10 ingprof voip aesencrypt disable active
on
OLT2406(config-remote-uniport)# exit
OLT2406(config)# exit
OLT2406# show remote uniport uniport-6-1-101-1-1 queue
Uniport TC Pri Wt UsBwProfileName DsBwProfileName DsOpt BwGrpShrId DsGrpShrId
--------------------------------------------------------------------------------------------------------------------------------
uniport-6-1-101-1-1 1 0 0 voice voice olt 1 1
OLT2406# show remote uniport uniport-6-1-101-1-1 vlan 10
|AID | UNI-VID Status NNI-VID Tag PBit_Prof DSCP_to_PBIT Ing_Prof TC GemP AES_Ept SP MN
-+---------------------+------------------------------------------------------------------------------------------------------
v|uniport-6-1-101-1-1 | 10 IS 10 tag inactive voip 1 260 disable of 1
-+---------------------+------------------------------------------------------------------------------------------------------
To Next Page
Loading...
