Siemens Simatic S7 Series

Index
S7-200 SMART
722 System Manual, 09/2015, A5E03822230-AC
executing multiple scans, 464
scan times (SMW22-SMW26), 673
SCR, 303
SCRE, 303
SCRT, 303
Security, 124
SEG, 198
Selecting the network cable, 402
Service and support, 3
Set and reset dominant bistable instructions, 160
Set and reset immediate instructions, 159
SET_ADDR, 190
SET_RTC, 165
SET_RTCX, 167
Setting the CPU type, 33
SFND (STL-Find string), 323
Shift and rotate instructions
bit (SHRB), 317
byte, word, dword, 315
SHL_B, 315
SHL_DW, 315
SHL_W, 315
SHR_B, 315
SHR_DW, 315
SHR_W, 315
SHRB, 317
SI (STL-set immediate), 159
Siemens technical support, 3
Signal board (SB
SB BA01 specifications, 646
Signal board (SB)
installing and removing, 47
SB AQ01 specifications, 642
SB AQ01 wiring diagram, 643
SB BA01 wiring diagram, 646
SB CM01 specifications, 644
SB CM01 wiring diagram, 645
SB DT04 specifications, 637
SB DT04 wiring diagram, 639
Signal board ID and error registers (SMB28-
SMB29), 673
Signal boards (SB)
analog output representation (current), 625
analog output representation (voltage), 625
input representation (current), 624
input representation (voltage), 624
Signal modules (SM)
step response times, 623
SIN (sine), 264
SIP_ADDR, 191
SLB (STL-Shift left byte), 315
SLD (STL-Shift left dword), 315
SLW (STL-Shift left word), 315
SM (Special memory) assignments and functions, 665
SM locations (Axis of Motion), 556
SM memory, PTO/PWM operation, 252
SMB0 system status bits, 667
SMB1 instruction execution status bits, 668
SMB1000-SMB1049 CPU hardware/firmware ID, 688
SMB1050-SMB1099 SB (signal board)
hardware/firmware ID, 688
SMB1100-SMB1299 EM (expansion module)
hardware/firmware ID, 689
SMB130 port 1 configuration, 674
SMB136-145 (HSC3) high-speed counter 3, 675
SMB186-SMB194 receive message control, 681
SMB2 Freeport receive character, 669
SMB28-SMB29 signal board ID and error
registers, 673
SMB3 Freeport character error, 669
SMB30 (port 0) and SMB130 (port 1)
configuration, 674
SMB34-SMB35 time interval values for timed
interrupts, 674
SMB36-45 (HSC0) high-speed counter 0, 675
SMB4 interrupt queue overflow, run-time program
error, interrupts enabled, Freeport transmitter idle,
value forced, 670
SMB46-55 (HSC1) high-speed counter 1, 675
SMB480-SMB515 Data log status, 685
SMB5 I/O error status bits, 670
SMB56-65 (HSC2) high-speed counter 2, 675
SMB566-SMB579: PTO2 and PWM2 high-speed
outputs,
SMB600-SMB649 Axis 0 motion control, 686
SMB66-SMB85, SMB166-SMB169, and SMB176-
SMB179: PTO0, PWM0, PTO1, and PWM1 high-speed
outputs,
SMB66-SMB85, SMB166-SMB169, SMB176-SMB179,
and SMB566-SMB579: PTO0, PWM0, PTO1, PWM1,
PTO2, and PWM2 high-
speed outputs,
SMB6-SMB7 CPU ID register, 671
SMB86-SMB94 and SMB186-SMB194 receive
message control, 681
SMB8-SMB19 I/O module ID and error registers, 672
SMW100-SMW114 System alarms, 684
SMW22-SMW26 scan times, 673
SMW98 I/O expansion bus - communication
errors, 683
Software debugging, 453
Special memory assignments and functions, 665
Special memory bytes
EM DP01 PROFIBUS DP, 385