RFL Electronics RFL 9300 - Figure 6-13. Typical Read Settings Menu for Three-Terminal Single-Pole Mode; Figure 6-14. Typical Read Settings Menu for Three-Terminal Three-Pole Mode

#
020
022
024
026
028
030
032
034
036
038
041
046
050
121
122
141
999
9300>
PARAMETER
Phase Bias
Bias Control
Bias/Ground Dly
F.D. Ground
Phase O/C Bkup
Phase TOC
(2)
PhTOC Curve
Ground TOC
(3)
Gd TOC Curve
Overhd/Undergd
Comms Alm Dly
Transmit Addr 1
Guard/Trip
Current Time
Reset Disp. Alrm
Slctv Pole RL
System Label
SETTING
1.500 Amps
Disable
.05/.05 sec
1.0 Amp
31.875 Amps
Disable
N/A
Disable
N/A
Overhead
Disable
4079
Disable
09:29:27
No
Disable
Gen1
#
021
023
025
027
029
031
033
035
037
040
044
047
120
140
145
PARAMETER
Ground Bias
Ground Delay
F.D. Phase
Backup
(1)
Ground O/C Bkup
Ph TOC Pickup
Ph TOC Dial
Gd TOC Pickup
Gd TOC Dial
Stub Bus
(1)
Beeper
Transmit Addr 2
Current Date
Single Pole
Trip Release
SETTING
1.500 Amps
Enable
8.0 Amps
Enable
31.000 Amps
N/A
N/A
N/A
N/A
Inactive
Disable
4075
08/16/00
Active
CS+TRIP
Figure 6-13. Typical read settings menu for three-terminal single-pole mode
#
020
022
024
026
028
030
032
034
036
038
040
044
047
120
122
145
999
9300>
PARAMETER
Phase Bias
Bias Control
Bias/Ground Dly
F.D. Ground
Phase O/C Bkup
Phase TOC
(2)
PhTOC Curve
Ground TOC
(3)
Gd TOC Curve
Overhd/Undergd
Stub Bus
(1)
Beeper
Transmit Addr 2
Current Date
Reset Disp. Alrm
Trip Release
System Label
SETTING
1.500 Amps
Disable
.05/.05 sec
1.0 Amp
31.875 Amps
Disable
N/A
Disable
N/A
Overhead
Inactive
Disable
4075
08/16/00
No
CS+TRIP
Gen1
#
021
023
025
027
029
031
033
035
037
039
041
046
050
121
140
PARAMETER
Ground Bias
Ground Delay
F.D. Phase
Backup
(1)
Ground O/C Bkup
Ph TOC Pickup
Ph TOC Dial
Gd TOC Pickup
Gd TOC Dial
Open Conductor
Comms Alm Dly
Transmit Addr 1
Guard/Trip
Current Time
Single Pole
SETTING
1.500 Amps
Enable
8.0 Amps
Enable
31.000 Amps
N/A
N/A
N/A
N/A
Alarm
Disable
4079
Disable
10:12:58
Inactive
Figure 6-14. Typical read settings menu for three-terminal three-pole mode
The following NOTES apply to Figures 6-11 through 6-14:
1. If Stub-Bus (parameter #40) is active, Backup (parameter #27) will show a setting of SBACTIVE. This indi-
cates that the relay has been placed in Backup Mode. See Section 3.13 for more information.
2. If parameter No. 030 is disabled, then parameter numbers 031, 032 and 033 will display N/A (not applicable).
3. If parameter No. 034 is disabled, then parameter numbers 035, 036 and 037 will display N/A (not applicable).
RFL 9300 RFL Electronics Inc.
January 30, 2002 6-43 (973) 334-3100