RFL Electronics RFL 9300 - Figure 6-16. Typical Remote Parameters Display for a Two-Terminal Single-Pole System; Figure 6-17. Typical Remote Parameters Display for a Two-Terminal Three-Pole System

6.5.7 REMOTE PARAMETERS DISPLAY
To view a list of the remote parameter settings, enter the “K” command.
Format: 9300>K[ENTER]
When the “K” command is entered, the screen on your terminal will be cleared and replaced by the REMOTE
PARAMETERS screen. Typical Remote Parameters displays are shown in Figures 6-16 through 6-19.
#
053
055
057
059
061
063
065
067
069
071
074
076
077
161
9300>
PARAMETER
R1 Phase Bias
R1 Bias Control
R1 Bias/Gnd Dly
R1 FD Ground
R1 Ph O/C Bkup
R1 Phase TOC
R1 Ph TOC Curve
R1 Ground TOC
R1 Gd TOC Curve
R1 Overhd/Undrgd
R1 DC Offset Flt
R1 PingPong
R1 CDC
R1 Slctv Pole RL
SETTING
1.500 Amps
Disable
.05/.05 sec
1.0 Amp
31.875 Amps
Disable
N/A
Disable
N/A
Overhead
Enable
004.0 ms
004.0 ms
Disable
#
054
056
058
060
062
064
066
068
070
073
075
160
165
PARAMETER
R1 Ground Bias
R1 Ground Delay
R1 FD Phase
R1 Backup
R1 Gnd O/C Bkup
R1 Ph TOC Pickup
R1 Ph TOC Dial
R1 Gd TOC Pickup
R1 Gd TOC Dial
R1 Stub Bus
R1 Guard/Trip
R1 Single Pole
Trip Rls
SETTING
1.500 Amps
Enable
8.0 Amps
Enable
31.000 Amps
31.875 Amps
N/A
31.000 Amps
N/A
Inactive
Disable
Active
TRIP+100
Figure 6-16. Typical Remote Parameters Display for a two-terminal single-pole system
#
053
055
057
059
061
063
065
067
069
071
073
075
077
165
9300>
PARAMETER
R1 Phase Bias
R1 Bias Control
R1 Bias/Gnd Dly
R1 FD Ground
R1 Ph O/C Bkup
R1 Phase TOC
R1 Ph TOC Curve
R1 Ground TOC
R1 Gd TOC Curve
R1 Overhd/Undrgd
R1 Stub Bus
R1 Guard/Trip
R1 CDC
R1 Trip Rls
SETTING
1.500 Amps
Disable
.05/.05 sec
1.0 Amp
31.875 Amps
Disable
N/A
Disable
N/A
Overhead
Inactive
Disable
004.0 ms
TRIP+100
#
054
056
058
060
062
064
066
068
070
072
074
076
160
PARAMETER
R1 Ground Bias
R1 Ground Delay
R1 FD Phase
R1 Backup
R1 Gnd O/C Bkup
R1 Ph TOC Pickup
R1 Ph TOC Dial
R1 Gd TOC Pickup
R1 Gd TOC Dial
R1 Open Cond
R1 DC Offset Flt
R1 PingPong
R1 Single Pole
SETTING
1.500 Amps
Enable
8.0 Amps
Enable
31.000 Amps
31.875 Amps
N/A
31.000 Amps
N/A
Alarm
Enable
004.0 ms
Inactive
Figure 6-17. Typical Remote Parameters Display for a two-terminal three-pole system
RFL 9300 RFL Electronics Inc.
January 30, 2002 6-45 (973) 334-3100