Topcon X35 - User Manual

328 pages

Save Page as PDF

To Next Page

X35 CONSOLE

BOURGAULT SRC

6000, 7000, 8000 & 9000 A/S

OPERATOR'S MANUAL

MONITOR VERSION: 4.04

REVISED DECEMBER 2019 0252-90-77

Use this manual as well as the Topcon Operator's Manual, and the Bourgault Air Seeder

Operator's Manual for operational information.

Original Instructions

Main Page

Other manuals for Topcon X35

Operator's Manual296 pages

Questions and Answers

K
Kimberly RichardsonSep 12, 2025
Why are alarms not activating on my Topcon X35?
- J
  jocelynthorntonSep 12, 2025
  If alarms are not activating on your Topcon Music Mixer, check alarm settings. In Setup screen go to System/Alarms.
M
Matthew HernandezSep 12, 2025
Why does the tank low alarm activate when the display shows product remaining in the Topcon X35?
- J
  justin31Sep 12, 2025
  If the tank low alarm activates on your Topcon Music Mixer but the display still shows product remaining in the tank, adjust tank capacity manually to account for the tank volume that was not filled.
J
James MannSep 12, 2025
What to do if Topcon X35 Music Mixer shows error messages on startup?
- J
  Jeff TaylorSep 12, 2025
  If the Topcon Music Mixer is showing error messages on startup, contact Bourgault dealer.
K
kcohenSep 9, 2025
What to do if Topcon Music Mixer display is blank after startup?
- E
  Elijah RamseySep 10, 2025
  If the Topcon Music Mixer is displaying a blank display after startup, contact Bourgault dealer.
H
Heather RodriguezSep 8, 2025
What to do if I cannot reach target metering rate on Topcon X35 Music Mixer?
- A
  Andrea BrennanSep 9, 2025
  If you cannot reach the target metering rate on your Topcon Music Mixer, ensure metering auger shaft is turning freely (no rubbing or foreign objects in housing). Change to higher range. Lower the rate.
R
Rebecca FrostSep 7, 2025
How do I fix no LEDs on the keypad of my Topcon X35?
- J
  justinramosSep 8, 2025
  If there are no LEDs on the keypad of your Topcon Music Mixer, adjust the brightness of the X35 monitor.
V
Victoria PayneAug 23, 2025
How to enable touch screen control buttons on Topcon Music Mixer?
- C
  Chad RushAug 23, 2025
  If the Topcon Music Mixer touch screen control buttons will not work, in the Setup screen, go to Implement/Operator Input and check if virtual switches are enabled.
R
Renee ScottSep 6, 2025
What to do if some LEDs are out on Topcon Music Mixer keypads?
- D
  Dr. Ryan PopeSep 6, 2025
  If some LEDs are out on keypads of your Topcon Music Mixer, restart the console/tractor to reboot system.
G
Gregory WatsonSep 4, 2025
Why is the area accumulation incorrect on my Topcon X35?
- T
  Theresa BellSep 5, 2025
  If the Topcon Music Mixer shows incorrect area accumulation, use GPS speed if possible. If not available, complete a distance check to verify wheel factor is incorrect, and if so, complete a wheel factor calibration. Enter the correct implement width.
E
Erica HernandezSep 3, 2025
How do I correct the incorrect ground speed display on my Topcon X35 Music Mixer?
- J
  Jeffery BlanchardSep 4, 2025
  If the Topcon Music Mixer is displaying an incorrect ground speed, use GPS speed if possible. If not available, complete a distance check to verify wheel factor is incorrect, and if so, complete a wheel factor calibration. Also, ensure proper alignment and gap. Ensure that the ground speed sensor to target gap is 1/32”-1/8” (1mm-3mm).