D-Link xStack DGS-3120 Series User Manual

xStack
®
DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
725
Chapter 71 OSPF Version 3 Command
List (RI Mode Only)
config ospfv3 router_id <ipaddr>
enable ospfv3
disable ospfv3
config ospfv3 [ipif <ipif_name 12> | all] {area <area_id> | priority <value 0-255> | hello_interval
<sec 1-65535> | dead_interval <sec 1-65535> | instance <value 0-255> | metric <value 1-
65535> | state [enable | disable] | passive [enable | disable]}(1)
show ospfv3 {[ipif <ipif_name 12> | all]}
create ospfv3 area <area_id> type [normal | stub {stub_summary [enable | disable] | metric
<value 0-65535>}]
config ospfv3 area <area_id> type [normal | stub {stub_summary [enable | disable] | metric
<value 0-65535>}]
delete ospfv3 area <area_id>
show ospfv3 area {<area_id>}
create ospfv3 aggregation <area_id> <ipv6networkaddr> advertise [enable | disable]
config ospfv3 aggregation <area_id> <ipv6networkaddr> advertise [enable | disable]
delete ospfv3 aggregation <area_id> <ipv6networkaddr>
show ospfv3 aggregation {<area_id>}
show ospfv3 lsdb {area <area_id> | type [rtrlink | netlink | inter_area_prefix | inter_area_router |
asextlink | link_lsa | intra_area_prefix]}
show ospfv3 neighbor {<neighbor_id> ipif <ipif_name 12>}
show ospfv3 virtual_neighbor {<area_id> <neighbor_id>}
create ospfv3 virtual_link <area_id> <neighbor_id> {hello_interval <sec 1-65535> |
dead_interval <sec 1-65535> | instance <value 0-255>}
config ospfv3 virtual_link <area_id> <neighbor_id> {hello_interval <sec 1-65535> |
dead_interval <sec 1-65535> |instance <value 0-255>}(1)
delete ospfv3 virtual_link <area_id> <neighbor_id>
show ospfv3 virtual_link {<area_id> <neighbor_id>}
create ipv6route redistribute dst ospfv3 src [local | static | ripng] {mettype [1 | 2] | metric <value
1-16777214>}
config ipv6route redistribute dst ospfv3 src [local | static | ripng] {mettype [1 | 2] | metric <value
1-16777214>}(1)
delete ipv6route redistribute dst ospfv3 src [local | static | ripng]
71-1 config ospfv3 router_id
Description
This command is used to configure the OSPFv3 router ID.
Format
config ospfv3 router_id <ipaddr>
Parameters
<ipaddr> - Enter a 32-bit number in the form of an IPv4 address that uniquely identifies the router
in the OSPFv3 domain. In OSPFv3, neighboring routers on a given link are always identified
by their OSPFv3 Router ID. Set 0.0.0.0 means auto-selected. Switch will select the largest

D-Link xStack DGS-3120 Series Specifications

General

MAC Address Table	16K entries
Ports	10/100/1000BASE-T ports
VLANs	4094
Jumbo Frame	Up to 9KB
Power Supply	Internal power supply (depending on model)
Power over Ethernet (PoE)	No
Layer 3 Features	RIP
Quality of Service (QoS)	8 queues per port, DiffServ
Security Features	ACLs
Management	Web-based, CLI, SNMP
Operating Temperature	0°C to 40°C
Storage Temperature	-40°C to 70°C
SFP Ports	Combo 10/100/1000BASE-T/SFP ports and/or dedicated SFP/SFP+ ports (depending on model)