D-Link xStack DGS-3120 Series User Manual

xStack
®
DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
517
Chapter 49 Japanese Web-Based
Access Control (JWAC)
Command List
enable jwac
disable jwac
config jwac [quarantine_server_url [<string 128> | ipv6 <string 128>] |
clear_quarantine_server_url {ipv6}]
show jwac
enable jwac redirect
disable jwac redirect
config jwac redirect {destination [quarantine_server | jwac_login_page] | delay_time <sec 0-
10>}(1)
enable jwac forcible_logout
disable jwac forcible_logout
enable jwac udp_filtering
disable jwac udp_filtering
enable jwac quarantine_server_monitor
disable jwac quarantine_server_monitor
config jwac quarantine_server_error_timeout <sec 5-300>
config jwac virtual_ip [<ipaddr> | <ipv6addr>] {url [<string 128> | clear]}
config jwac update_server [add | delete] [ipaddress <network_address> | ipv6address
<ipv6networkaddr>] {[tcp_port <port_number 1-65535> | udp_port <port_number 1-65535>]}
config jwac switch_http_port <tcp_port_number 1-65535> {[http | https]}
config jwac ports [<portlist> | all] { state [enable | disable] | max_authenticating_host <value 0-
50> | aging_time [infinite | <min 1-1440>] | idle_time [infinite | <min 1-1440>] | block_time
[<sec 0-300>]}(1)
show jwac ports {<portlist>}
config jwac radius_protocol [local | eap_md5 | pap | chap | ms_chap | ms_chapv2]
create jwac user <username 15> {vlan <vlanid 1-4094>}
config jwac user <username 15> {vlan <vlanid 1-4094>}
delete jwac [user <username 15> | all_users]
show jwac user
clear jwac auth_state [ports [all | <portlist>] {authenticated | authenticating | blocked} | mac_addr
<macaddr>]
show jwac auth_state ports {<portlist>}
config jwac authorization attributes {radius [enable | disable] | local [enable | disable]}(1)
show jwac update_server
config jwac authentication_page element [japanese | english] [default | page_title <desc 128> |
login_window_title <desc 32> | user_name_title <desc 16> | password_title <desc 16> |
logout_window_title <desc 32> | notification_line <value 1-5> <desc 128>]
config jwac authenticate_page [japanese | english]
show jwac authenticate_page
49-1 enable jwac
Description
This command is used to enable the Japanese Web-based access control (JWAC) function. JWAC
and WAC are mutually exclusive functions. That is, they can not be enabled at the same time.

D-Link xStack DGS-3120 Series Specifications

General

MAC Address Table	16K entries
Ports	10/100/1000BASE-T ports
VLANs	4094
Jumbo Frame	Up to 9KB
Power Supply	Internal power supply (depending on model)
Power over Ethernet (PoE)	No
Layer 3 Features	RIP
Quality of Service (QoS)	8 queues per port, DiffServ
Security Features	ACLs
Management	Web-based, CLI, SNMP
Operating Temperature	0°C to 40°C
Storage Temperature	-40°C to 70°C
SFP Ports	Combo 10/100/1000BASE-T/SFP ports and/or dedicated SFP/SFP+ ports (depending on model)