D-Link xStack DGS-3120 Series User Manual

xStack
®
DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
802
Chapter 81 PIM for IPv6 Command List
(RI Mode Only)
config pim6 [ipif <ipif_name 12> | all] {hello_interval <sec 0-18000> | triggered_hello_delay <sec
0-60> | propagation_delay <sec 0-32> | override_interval <sec 0-65> | jp_interval <sec 0-
18000> | dr_priority <uint 0-4294967294> | bsr_border [disable | enable] | stub_interface
[disable | enable] | state [enable | disable]}(1)
show pim6 {ipif <ipif_name 12>}
config pim6 cbsr {ipif <ipif_name 12> state [enable | disable] | priority <value 0-255> |
hash_masklen <value 0-128>}(1)
show pim6 cbsr
config pim6 crp [rp <ipif_name 12> | all] {priority <value 0-255> | interval <sec 1-16383>}(1)
create pim6 crp group <ipv6networkaddr> rp <ipif_name 12>
delete pim6 crp group <ipv6networkaddr>
enable pim6
disable pim6
config pim6 last_hop_spt_switchover [never | immediately]
show pim6 neighbor {ipif <ipif_name 12>}
show pim6 mroute {group <ipv6addr> {source <ipv6addr>}}
show pim6 mroute star_g {group <ipv6addr> {ipif <ipif_name 12>}}
show pim6 mroute s_g {rpt} {group <ipv6addr> source <ipv6addr> {ipif <ipif_name 12>}}
create pim6 static_rp group <ipv6networkaddr> rp <ipv6addr> {override_dynamic}
delete pim6 static_rp group <ipv6networkaddr>
config pim6 embedded_rp state [enable | disable]
show pim6 crp
show pim6 static_rp
show pim6 rpset
config pim6 register_checksum_calculate [include_data | not_include_data]
config pim6 register_probe_time <sec 1-127>
config pim6 register_suppression_time <sec 3-65535>
config pim6 keepalive_period <sec 120-65535>
81-1 config pim6
Description
This command is used to set the PIM6 multicast protocol state and some related parameters in the
protocol on some interfaces.
Format
config pim6 [ipif <ipif_name 12> | all] {hello_interval <sec 0-18000> | triggered_hello_delay
<sec 0-60> | propagation_delay <sec 0-32> | override_interval <sec 0-65> | jp_interval <sec
0-18000> | dr_priority <uint 0-4294967294> | bsr_border [disable | enable] | stub_interface
[disable | enable] | state [enable | disable]}(1)
Parameters
ipif - Specify to apply the configurations to this specific IP interface.
<ipif_name 12> - Enter the IP interface name.
all - Specify to apply the configurations to all IP interfaces.

D-Link xStack DGS-3120 Series Specifications

General

MAC Address Table	16K entries
Ports	10/100/1000BASE-T ports
VLANs	4094
Jumbo Frame	Up to 9KB
Power Supply	Internal power supply (depending on model)
Power over Ethernet (PoE)	No
Layer 3 Features	RIP
Quality of Service (QoS)	8 queues per port, DiffServ
Security Features	ACLs
Management	Web-based, CLI, SNMP
Operating Temperature	0°C to 40°C
Storage Temperature	-40°C to 70°C
SFP Ports	Combo 10/100/1000BASE-T/SFP ports and/or dedicated SFP/SFP+ ports (depending on model)