D-Link xStack DGS-3120 Series User Manual

xStack
®
DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
243
Chapter 22 Debug Software Command
List
debug error_log [dump | clear | upload_toTFTP <ipaddr> <path_filename 64>]
debug show error_reboot state
debug buffer [utilization | dump | clear | upload_toTFTP <ipaddr> <path_filename 64>]
debug output [module <module_list> | all] [buffer | console]
debug config error_reboot [enable | disable]
debug config state [enable | disable]
debug clear cpu port counter [<portlist> | all]
debug show cpu port counter [<portlist> | all] [by_cos | by_reason | by_protocol [L2 | ARP | IPv4
[ICMP | TCP | UDP | multicast-protocol | unicast-protocol | all] | IPv6 [ICMP | TCP | UDP |
OSPFV3 | all] | STACK] | by_priority]
debug show jwac auth_info
debug show status {module <module_list>}
debug dhcpv6_client state enable
debug dhcpv6_client state disable
debug dhcpv6_client output [buffer | console]
debug dhcpv6_client packet [all | receiving | sending] state [enable | disable]
debug dhcpv6_relay state enable
debug dhcpv6_relay state disable
debug dhcpv6_relay output [buffer | console]
debug dhcpv6_relay packet [all | receiving | sending] state [enable | disable]
debug dhcpv6_relay hop_count state [enable | disable]
debug address_binding [event | dhcp | all] state [enable | disable] (RI and EI Mode Only)
debug ripng state enable (RI Mode Only)
debug ripng state disable (RI Mode Only)
debug ripng show flag (RI Mode Only)
debug ripng flag [{interface | packet [all | rx | tx ] | route} | all] state [enable | disable] (RI Mode
Only)
no debug address_binding (RI and EI Mode Only)
debug show address_binding binding_state_table [nd_snooping | dhcpv6_snooping] (RI
and EI Mode Only)
debug ospf [neighbor_state_change | interface_state_change {dr_bdr_selection} | lsa {all |
originating | installing | receiving | flooding}(1) | packet {all | receiving | sending}(1) |
retransmission | spf {all | intra | inter | extern}(1) | timer | virtual_link | route | redistribution]
state [enable | disable] (RI Mode Only)
debug ospf clear counter {packet | neighbor | spf} (RI Mode Only)
debug ospf log state [enable | disable] (RI Mode Only)
debug ospf show counter {packet | neighbor | spf} (RI Mode Only)
debug ospf show detail external_link (RI Mode Only)
debug ospf show detail net_link (RI Mode Only)
debug ospf show detail rt_link (RI Mode Only)
debug ospf show detail summary_link (RI Mode Only)
debug ospf show detail type7_link (RI Mode Only)
debug ospf show flag (RI Mode Only)
debug ospf show log state (RI Mode Only)
debug ospf show redistribution (RI Mode Only)
debug ospf show request_list (RI Mode Only)
debug ospf show summary_list (RI Mode Only)
debug ospf state [enable | disable] (RI Mode Only)
debug vrrp [vr_state_change | packet [all | {receiving | sending}(1)] | mac_addr_update |
interface_change | timers] state [enable | disable] (RI Mode Only)

D-Link xStack DGS-3120 Series Specifications

General

MAC Address Table	16K entries
Ports	10/100/1000BASE-T ports
VLANs	4094
Jumbo Frame	Up to 9KB
Power Supply	Internal power supply (depending on model)
Power over Ethernet (PoE)	No
Layer 3 Features	RIP
Quality of Service (QoS)	8 queues per port, DiffServ
Security Features	ACLs
Management	Web-based, CLI, SNMP
Operating Temperature	0°C to 40°C
Storage Temperature	-40°C to 70°C
SFP Ports	Combo 10/100/1000BASE-T/SFP ports and/or dedicated SFP/SFP+ ports (depending on model)