EasyManuals Logo

D-Link xStack DGS-3120 Series User Manual

D-Link xStack DGS-3120 Series
1150 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #767 background imageLoading...
Page #767 background image
xStack
®
DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
762
vlanid - Specify the VLAN ID used here.
<vidlist> - Enter the VLAN ID used here.
max_learning_addr - Specify the maximum learning address value.
<max_lock_no 0-3072> - Enter the maximum learning address value here. This value
must be between 0 and 3072.
no_limit - Specify that the maximum learning address value will be set to no limit.
Restrictions
Only Administrator, Operator and Power-User level users can issue this command.
Example
To configure the port-based port security setting so that the maximum number of port security
entries is restricted to 10, and the lock_address mode is set to permanent on port 6:
DGS-3120-24TC:admin#config port_security ports 1:6 admin_state enable
max_learning_addr 10 lock_address_mode permanent
Command: config port_security ports 1:6 admin_state enable max_learning_addr 10
lock_address_mode permanent
Success.
DGS-3120-24TC:admin#
76-3 config port_security vlan
Description
This command is used to set the maximum number of port security entries that can be learned on
a specific VLAN.
There are four levels that limit the number of learned entries; the entire system, a port, a VLAN,
and a specific VLAN on a port. If any limitation is exceeded, the new entry will be discarded.
Format
config port_security vlan [<vlan_name 32> | vlanid <vidlist>] max_learning_addr
[<max_lock_no 0-3072> | no_limit]
Parameters
vlan - Specify the VLAN by name.
<vlan_name 32> - Enter the VLAN name here. This name can be up to 32 characters long.
vlanid - Specify a list of VLANs by VLAN ID.
<vidlist> - Enter the VLAN ID list here.
max_learning_addr - Specify the maximum number of port security entries that can be learned
by this VLAN. If this parameter is set to 0, it means that no user can be authorized on this
VLAN. If the setting is lower than the number of current learned entries on the VLAN, the
command will be rejected. The default value is “no_limit”
<max_lock_no 0-3072> - Enter the maximum number of port security entries that can be
learned here. This value must be between 0 and 3072.
no_limit - No limitation on the number of port security entries that can be learned by a specific
VLAN.

Table of Contents

Other manuals for D-Link xStack DGS-3120 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the D-Link xStack DGS-3120 Series and is the answer not in the manual?

D-Link xStack DGS-3120 Series Specifications

General IconGeneral
MAC Address Table16K entries
Ports10/100/1000BASE-T ports
VLANs4094
Jumbo FrameUp to 9KB
Power SupplyInternal power supply (depending on model)
Power over Ethernet (PoE)No
Layer 3 FeaturesRIP
Quality of Service (QoS)8 queues per port, DiffServ
Security FeaturesACLs
ManagementWeb-based, CLI, SNMP
Operating Temperature0°C to 40°C
Storage Temperature-40°C to 70°C
SFP PortsCombo 10/100/1000BASE-T/SFP ports and/or dedicated SFP/SFP+ ports (depending on model)

Related product manuals