Krone Comprima CF 155 XC - 14.1 Lubricants; 14.2 General aspects; 14.3 Lubricating the PTO shaft

Maintenance – lubrication
330
Pos: 59.192.7 /Übersc hriften/Überschr iften 2/P-T/Schmier fette / Schmieröle @ 24\mo d_1241676102945_78. docx @ 247353 @ 2 @ 1
14.1 Lubricants
Pos: 59.192.8 /BA/W artung/Großpackenpr essen/Schmierung / Sc hmierplan/Allgemei nes unterschiedlic he Schmiersysteme @ 24\mod_1 241676457180_7 8.docx @ 247436 @ 2 @ 1
14.2 General aspects
Depending on the design, the machine may be equipped with different lubrication systems.
Soft, supple NLGI Class 2 lithium soap greases in accordance with DIN 51825 should be used
as lubricating greases. We recommend that you do not use lubricating greases with any other
base material.
Note
Do not use greases containing graphite! There may be problems when different greases are
mixed together!
Pos: 59.192.9 /BA/W artung/Großpackenpr essen/Schmierung / Sc hmierplan/Tabelle Sc hmierstoffe @ 24\mod_124 1681229992_78.doc x @ 247460 @ @ 1
Manufacturer Lubricants based on
mineral oil
Bio-lubricants
ARAL Long-term grease H
On request
BP Energrease LS-EP2
DEA Glissando EP2
FINA Marson EPL 2A
Shell Alvania Ep2
ESSO EGL 3144
Pos: 59.192.10 /BA/W artung/Großpackenpr essen/Schmierung / Sc hmierplan/Abschmier en Text allgemein @ 24\mo d_1241683749117_78 .docx @ 247535 @ @ 1
Lubrication points on the machine must be lubricated at regular intervals. The position of the
lubrication points and the lubrication intervals can be seen in the lubrication plans in the
operating instructions. Remove the grease that comes out of the bearing points after lubrication.
Pos: 59.192.11 /Übersc hriften/Übersc hriften 2/A-E/Absc hmieren der Gelenkwelle @ 0\mod_1197359496183_7 8.docx @ 18251 @ 2 @ 1
14.3 Lubricating the PTO shaft
Pos: 59.192.12 /BA/W artung/Rundballenpre sse/Schmierung/ Schmierplan/Bild Ge lenkwelle VP @ 35\mod_125613 2667597_78.doc x @ 326692 @ @ 1
Fig. 260
Pos: 59.192.13 /BA/W artung/Gelenkwelle sc hmieren/Abschmier en Gelenkwelle Text @ 16\ mod_1235638171674_78. docx @ 199556 @ @ 1
Lubricate the PTO shafts at the intervals indicated in the drawing with a multi-purpose grease.
Follow the operating instructions of the PTO shaft manufacturer.
Pos: 59.192.14 /BA/Si cherheit/Zapfwel lenbetrieb Zusatz @ 2\mod_12 03524761314_78.doc x @ 66513 @ @ 1
Note
The instructions of the manufacturer must be observed with regard to the PTO shaft. (separate
operating instructions)
Pos: 59.192.15 /Layout Module /------ ---------Seitenumbruc h---------------- @ 0\mod_1196175311226_0. docx @ 4165 @ @ 1