357
Number slide wrappings ................................... 136
O
Oil Level Check and Oil Change Intervals
(Gearboxes) .................................................. 295
Oil Level Check and Oil Change on the
Gearboxes .................................................... 295
On-board Hydraulic Sytem ............................... 313
Operation .......................................................... 209
Operation of the Hydraulic Zero Setting of Blades
(Optional) ...................................................... 203
Operational safety: Technically perfect condition
........................................................................ 16
Overload protection .......................................... 222
P
Parking ................................................................ 99
Parking brake ...................................................... 44
Parking Support .................................................. 47
Parking the machine safely ................................ 21
Personal protective equipment ........................... 19
Personnel qualification........................................ 14
Physical messages ........................................... 194
Pick-up ...................................................... 223, 306
Placing in Storage ............................................. 337
Platform on the Wrapping Table ......................... 51
Position of the Adhesive Safety Stickers on the
Machine .......................................................... 28
Position of the Sensors ..................................... 279
Preparations for road travel ................................ 96
Preparing the machine for repair, maintenance
and adjustment work ....................................... 27
Pre-signalling .................................................... 131
PTO shaft ............................................................ 65
Purpose of Use ................................................... 13
R
Rear Floor Conveyor Drive ............................... 305
Reduce the Pressure on the Side Walls of the
Bale Chamber ............................................... 215
Releasing tension on the floor conveyor .......... 221
Releasing the Net Brake ................................... 270
Removing the transport holding down tensioning
device.............................................................. 60
Remowing the Crop Blockages in the Crop
Collection Area ............................................. 265
Re-Ordering the Adhesive Safety and Information
Labels ............................................................. 42
Roller crop guide ............................................... 225
Rollers on the Wrapping Table ........................... 50
Running-in period ............................................... 85
S
Safety .................................................................. 13
Safety routines ................................................... 25
Safety signs on the machine .............................. 20
Select day/night display lighting ....................... 182
Select the Number of Net Winds ..................... 244
Sensitivity of the Direction Display ................... 130
Service ............................................................. 160
Set Baling Pressure ......................................... 236
Setting Cut-off Position .................................... 245
Setting of the Brakes with Hydraulic Linkage
Setter ........................................................... 290
Setting of the Feed Position ............................. 243
Setting of the Scraper Rail to the Upper Spiral
Roller ............................................................ 277
Setting of the Tying position ............................ 244
Setting the Net Brake ....................................... 269
Setting the Pre-stretch of the Foil .................... 263
Settings .................................................... 126, 269
Sheet width ...................................................... 139
Shut-off valve for tailgate ........................... 48, 312
Slip-on Gear ..................................................... 297
Sources of danger on the machine .................... 22
Spare Parts ...................................................... 275
Starting the machine safely ............................... 27
Start-up .............................................................. 70
Start-up bale turner ............................................ 88
Status messages ............................................. 148
Step for working on the linkage ......................... 49
Stop Points ......................................................... 46
Stopping and securing the machine .................. 25
Store Bale ........................................................ 256
Structural changes to the machine .................... 15
Supporting lifted machine and machine parts
securely .......................................................... 25
Switch to different terminal .............................. 185
Switching on/off wrapping arm ......................... 154
Switching the terminal on / off when the machine
is connected ................................................. 109
Switching the terminal on / off when the machine
is not connected ........................................... 108
T
Tandem Axle .................................................... 288
Target group of this document ........................... 11
Technical data .................................................... 53
Technician ........................................................ 179
Tensioning the Drive Chains ............................ 304
Tensioning the floor conveyor .......................... 220
Tightening torques ........................................... 286
Tightening torques (countersunk screws) ........ 287
Torn sheet control ............................................ 140
Total bale counter ............................................ 145
To Next Page
Loading...
