Why are printouts from my Kyocera TASKalfa 400ci All in One Printer wrinkled?
Wrinkled printouts from your Kyocera All in One Printer could be due to: * A dirty paper separator of the paper feed unit. Clean the paper separator. * Damp paper. Replace the paper with new paper.
Why are images skewed when printing from my Kyocera All in One Printer?
Skewed images from your Kyocera All in One Printer may be caused by: * Incorrectly placed originals on the platen. Align them with the original size indicator plates. * Incorrectly placed originals in the optional document processor. Align the original width guides securely before placing the originals. * Incorrectly loaded paper. Check the position of the paper width guides.
Why does my Kyocera All in One Printer often jam?
Frequent paper jams in your Kyocera All in One Printer could be due to: * Incorrectly loaded paper. Load the paper correctly. * Unsupported or poor condition paper. Remove the paper, turn it over, and reload it. * Curled, folded, or wrinkled paper. Replace the paper with new paper. * Loose scraps or jammed paper in the machine. Remove any jammed paper.
What to do if my Kyocera TASKalfa 400ci displays machine failure?
First, turn the main power switch off and then on again, or unplug the power cord and plug it back in. If the error message persists, make a note of the error code, then turn off the main power switch, unplug the power cord, and call your service representative.
Why Kyocera TASKalfa 400ci All in One Printer cannot use the remote switching function?
If you cannot use the remote switching function, consider these potential causes: * If a pulse line is used, some phones may transmit tone signals using buttons. Refer to the operation manual of your phone set. * Verify the remote switching number is correct. The default number is 55.
What to do if Kyocera TASKalfa 400ci All in One Printer displays 'FAX box limit exceeded'?
If the FAX Box limit is exceeded on your Kyocera All in One Printer, it means the FAX Box capacity is full with document data. Press [End] to cancel the job. To proceed, either print or delete the data in the FAX Box, and then try the job again.
What to do if Kyocera Software application does not start?
If the Kyocera Software application doesn't start, it could be due to several reasons. First, your PC might not meet the necessary system requirements; in this case, consider upgrading your PC. Another possibility is low memory; try closing any unnecessary applications. Also, ensure that you are not trying to run two instances of the application simultaneously, as this is not supported.
How to fix light printouts on my Kyocera All in One Printer?
If your Kyocera All in One Printer's printouts are too light, consider the following: * If the machine is in Auto Density mode, set the correct density level for auto density. * If the machine is in Manual Density mode, use [Image Quality] to set the correct density level. * Shake the toner container from side to side several times to evenly distribute the toner. * If there is a message indicating the addition of toner, replace the toner container. * If the paper is damp, replace it with new paper. * Carry out Drum Refresh. * Carry out Developer Refresh. * Carry out Laser Scanner Cleaning. * If EcoPrint mode is enabled, disable it.
Why my Kyocera TASKalfa 400ci cannot print?
There could be several reasons why your Kyocera All in One Printer cannot print: * The power cord might not be plugged into an AC outlet. Plug it in. * The main power switch might not be turned on. Turn it on. * The printer cable might not be connected securely. Connect the correct printer cable securely. * The machine might have been powered on before the printer cable was connected. Power on the machine after connecting the printer cable. * 'Press Status Key...' might be displayed at the top of the screen. Press the Status/Job Cancel key, [Printing Jobs], and then [Resume All Print Jobs] to restart printing.
What to do if my Kyocera TASKalfa 400ci has a paper jam?
If a paper jam occurs, the Kyocera All in One Printer will stop, and the location of the jam will be indicated on the touch panel. Leave the machine on and follow the instructions to remove the jammed paper.
General| Brand | Kyocera |
|---|---|
| Model | TASKalfa 400ci |
| Category | All in One Printer |
| Language | English |
To Next Page
