2JZ/2JX/2JV/2H7-1
2-3-38
Connector Pin No. Signal I/O Voltage Description
YC1 1 +3.3V1 I 3.3 V DC 3.3 V DC power to FRPWB-S
Connected
to the main
front PWB
2 +5V1 I 5 V DC 5 V DC power to FRPWB-S
3 +24V1 I 24 V DC 24 V DC power to FRPWB-S
4 EEP SCLK I 0/3.3 V DC (pulse) EEPROM clock signal
5 EEP SDA I/O 0/3.3 V DC (pulse) EEPROM data signal
6 FRONT OPEN O 0/3.3 V DC FCSW: On/Off
7 GND - - Ground
8 GND - - Ground
9 GND - - Ground
YC2 1 FDLPFAN1 I 0/24 V DC DEVFM1: On/Off
Connected
to the
engine PWB
2 FDLPFAN2 I 0/24 V DC DEVFM2: On/Off
3 WTNR_LED I 0/5 V DC (pulse) WTLED LED emitter signal
4 WTNR_SENS O Analog WTS detection signal
5 WTB - - Not used
6 VCONT Y I Analog TS-Y control signal
7 TPD-1 Y O Analog TS-Y detection signal
8 POS SEN Y O 0/3.3 V DC DPS-Y: On/Off
9 ERS_Y I 24/0 V DC CL-Y: On/Off
10 VCONT C I Analog TS-C control signal
11 TPD-1 C O Analog TS-C detection signal
12 POS SEN C O 0/3.3 V DC DPS-C: On/Off
13 ERS_C I 24/0 V DC CL-C: On/Off
14 VCONT M I Analog TS-M control signal
15 TPD-1 M O Analog TS-M detection signal
16 POS SEN M O 0/3.3 V DC DPS-M: On/Off
17 ERS_M I 24/0 V DC CL-M: On/Off
YC3 1 ERASER Y O 24 V DC 24 V DC power to CL-Y
Connected
to the clean-
ing lamp Y,
drum PWB
Y and drum
position
sensor Y
2 ERS DR O 24/0 V DC CL-Y: On/Off
3 +3.3V1 O 3.3 V DC 3.3 V DC power to DRPWB-Y
4 EEP SCL O 0/3.3 V DC (pulse) DRPWB-Y EEPROM clock signal
5 EEPSDA I/O 0/3.3 V DC (pulse) DRPWB-Y EEPROM data signal
6 GND - - Ground
7 A0(GND) - - Ground
8 A1(OPEN) - - Not used
9 5V1 O 5 V DC 5 V DC power to DPS-Y
10 POS SENS 3 I 0/3.3 V DC DPS-Y: On/Off
11 GND - - Ground
YC4 1 GND - - Ground
Connected
to the devel-
oping PWB
Y
2 SDA I/O 0/3.3 V DC (pulse) DEVPWB-Y EEPROM data signal
3 SCK O 0/3.3 V DC (pulse) DEVPWB-Y EEPROM clock signal
4 +3.3V1 O 3.3 V DC 3.3 V DC power to DEVPWB-Y
5 TPD3 I Analog TS-Y detection signal
6 24V1 O 24 V DC 24 V DC power to DEVPWB-Y
7 VCONT 3 O Analog TS-Y control signal
To Next Page
Loading...
