Kyocera TASKalfa 400ci - Connector YC13

2JZ/2JX/2JV/2H7
2-3-13
YC13 A1 SCCLK O 0/3.3 V DC (pulse) PM clock signal
Connected
to the poly-
gon motor,
APC PWB
M/C/Y/K, PD
PWB and
inner tem-
perature
sensor 1
A2 SCRDY I 0/3.3 V DC PM ready signal
A3 SCREM O 0/3.3 V DC PM: On/Off
A4 SGND - - Ground
A5 +24V1 O 24 V DC 24 V DC power to PM
A6 +5V2 O 5 V DC 5 V DC power to APCPWB-Y
A7 APC3 CNT O Analog APCPWB-Y control signal
A8 SGND - - Ground
A9 ENBL3 O 0/3.3 V DC APCPWB-Y enable signal
A10 S/H3 O 0/3.3 V DC APCPWB-Y sample/hold signal
A11 VDO3 P O 0/3.3 V DC (pulse) Video data signal (P)
A12 VDO3 N O 0/3.3 V DC (pulse) Video data signal (N)
A13 +5V2 O 5 V DC 5 V DC power to APCPWB-M
A14 APC1 CNT O Analog APCPWB-M control signal
A15 SGND - - Ground
A16 ENBL1 O 0/3.3 V DC APCPWB-M enable signal
A17 S/H1 O 0/3.3 V DC APCPWB-M sample/hold signal
A18 VDO1 P O 0/3.3 V DC (pulse) Video data signal (P)
A19 VDO1 N O 0/3.3 V DC (pulse) Video data signal (N)
B1 +5V2 O 5 V DC 5 V DC power to PDPWB
B2 PD I 0/3.3 V DC (pulse) PD signal
B3 SGND - - Ground
B4 IN TEMP1 I Analog INTEMS1 detection signal (25/25, 30/30 ppm
model)
NC - - Not used (40/40, 50/40 ppm model)
B5 SGND - - Ground (25/25, 30/30 ppm model)
NC - - Not used (40/40, 50/40 ppm model)
B6 +5V2 O 5 V DC 5 V DC power to APCPWB-C
B7 APC2 CNT O Analog APCPWB-C control signal
B8 SGND - - Ground
B9 ENBL2 O 0/3.3 V DC APCPWB-C enable signal
B10 S/H2 O 0/3.3 V DC APCPWB-C sample/hold signal
B11 VDO2 P O 0/3.3 V DC (pulse) Video data signal (P)
B12 VDO2 N O 0/3.3 V DC (pulse) Video data signal (N)
B13 +5V2 O 5 V DC 5 V DC power to APCPWB-K
B14 APC4 CNT O Analog APCPWB-K control signal
B15 SGND - - Ground
B16 ENBL4 O 0/3.3 V DC APCPWB-K enable signal
B17 S/H4 O 0/3.3 V DC APCPWB-K sample/hold signal
B18 VDO4 P O 0/3.3 V DC (pulse) Video data signal (P)
B19 VDO4 N O 0/3.3 V DC (pulse) Video data signal (N)
Connector Pin No. Signal I/O Voltage Description