Kyocera TASKalfa 400ci - Connector YC19, YC20

2JZ/2JX/2JV/2H7
2-3-17
YC19 1 ERS1_DR O 24/0 V DC CL-M: On/Off
Connected
to the sub
front PWB
2 DRM1_POSITIO
N
I 0/3.3 V DC DPS-M: On/Off
3 TPD1 I Analog TS-M detection signal
4 DLP_VCONT1 O Analog TS-M control signal
5 ERS2_DR O 24/0 V DC CL-C: On/Off
6 DRM2_POSITIO
N
I 0/3.3 V DC DPS-C: On/Off
7 TPD2 I Analog TS-C detection signal
8 DLP_VCONT2 O Analog TS-C control signal
9 ERS3_DR O 24/0 V DC CL-Y: On/Off
10 DRM3_POSITIO
N
I 0/3.3 V DC DPS-Y: On/Off
11 TPD3 I Analog TS-Y detection signal
12 DLP_VCONT3 O Analog TS-Y control signal
13 WTNR_SET - - Not used
14 WTNER_CHEC
K
I Analog WTS detection signal
15 WTNR_LED O 0/5 V DC (pulse) WTLED LED emitter signal
16 FRONTDLP2_F
AN
O 0/24 V DC DEVFM2: On/Off
17 FRONTDLP1_F
AN
O 0/24 V DC DEVFM1: On/Off
18 PAPER FAN - - Not used
19 24V1 - - Not used
YC20 A1 DU MT CLK O 0/3.3 V DC (pulse) DUM clock signal
Connected
to the feed
PWB
A2 LOOP FAN O 0/3.3 V DC LFM: On/Off
A3 DU MT DR O 0/3.3 V DC DUM: On/Off
A4 FEED MT RDY I 0/3.3 V DC PCM ready signal
A5 FEED MT DR O 0/3.3 V DC PCM: On/Off
A6 FEED MT DIR O 0/3.3 V DC PCM drive switch signal
A7 FEED MT CLK O 0/3.3 V DC (pulse) PCM clock signal
A8 FED2 CLT REM O 0/24 V DC PFCL2: On/Off
A9 CAS2 EMPTY I 0/3.3 V DC PSW2: On/Off
A10 CAS2 LIFT UP I 0/3.3 V DC LSW2: On/Off
A11 CAS1 EMPTY I 0/3.3 V DC PSW1: On/Off
A12 CAS1LIFT UP I 0/3.3 V DC LSW1: On/Off
A13 LFT2 MT LOCK I 0/3.3 V DC LM2 lock signal
A14 LFT1 MT LOCK I 0/3.3 V DC LM1 lock signal
A15 LFT2 MT DR O 0/24 V DC LM2: On/Off
A16 LFT1 MT DR O 0/24 V DC LM1: On/Off
A17 LFT2 MT SIG1 I 0/3.3 V DC LM2 paper gauge signal
A18 LFT2 MT SIG2 I 0/3.3 V DC LM2 paper gauge signal
A19 LFT1 MT SIG1 I 0/3.3 V DC LM1 paper gauge signal
A20 LFT1 MT SIG2 I 0/3.3 V DC LM1 paper gauge signal
B1 MT_PD O 0/3.3 V DC PCM current control signal
Connector Pin No. Signal I/O Voltage Description