2JZ/2JX/2JV/2H7
2-3-19
YC23
1 5V SENSOR
LED
O 5 V DC 5 V DC power to MPPLSW
Connected
to the MP
paper size
length
switch, MP
tray switch,
MP paper
size width
switch, MP
paper
switch, MP
paper feed
switch, MP
solenoid
and Mp
paper feed
clutch
2 MPF LENGTH I 0/3.3 V DC MPPLSW: On/Off
3 PGND - - Ground
4 MPF TABLE I 0/3.3 V DC MPTSW: On/Off
5 PGND - - Ground
6 MPF_WIDTH1 I 0/3.3 V DC MPPWSW: On/Off
7 MPF_WIDTH2 I 0/3.3 V DC MPPWSW: On/Off
8 MPF_WIDTH3 I 0/3.3 V DC MPPWSW: On/Off
9 PGND - - Ground
10 PGND - - Ground
11 MPF PPR SET I 0/3.3 V DC MPPSW: On/Off
12 +5V1 O 5 V DC 5 V DC power to MPPSW
13 PGND - - Ground
14 MPF JAM1 I 0/3.3 V DC MPPFSW: On/Off
15 +5V1 O 5 V DC 5 V DC power to MPPFSW
16 +24V1 O 24 V DC 24 V DC power to MPSOL
17 MPF SOL1 DR O 0/24 V DC MPSOL: On/Off (ACT)
18 MPF SOL2 DR O 0/24 V DC MPSOL: On/Off (REV)
19 +24V1 O 24 V DC 24 V DC power to MPPFCL
20 MPF CLT REM O 0/24 V DC MPPFCL: On/Off
YC24 1 MPF_MOT_CLK O 0/3.3 V DC (pulse) MPM clock signal
Connected
to the MP
motor
2 MPF_MOT_DIR O 0/3.3 V DC MPM drive switch signal
3 MPF_MOT_DR O 0/3.3 V DC MPM: On/Off
4MPF_MOT_RD
Y
I 0/3.3 V DC MPM ready signal
5 PGND - - Ground
6 PGND - - Ground
7 +24V1 O 24 V DC 24 V DC power to MPM
8 +24V1 O 24 V DC 24 V DC power to MPM
YC25 A1 NC - - Not used
Connected
to the eject
motor, paper
full sensor,
fuser motor,
fuser clutch
and fuser
fan motor
A2 +24V2 O 24 V DC 24 V DC power to EM
A3 GND - - Ground
A4 +5V1 O 5 V DC 5 V DC power to EM
A5 EXIT MOT DR O 0/3.3 V DC EM: On/Off
A6 EXIT MOT CLK O 0/3.3 V DC (pulse) EM clock signal
A7 EXIT MOT DIR O 0/3.3 V DC EM drive switch signal
A8 EXIT MOT
LOCK
I 0/3.3 V DC EM lock signal
A9 EXIT MOT GAIN O 0/3.3 V DC EM gain signal
A10 GND - - Ground
A11 OVER_FLOW I 0/3.3 V DC PFS: On/Off
A12 +5V1 O 5 V DC 5 V DC power to PFS
B1 +24V2 O 24 V DC 24 V DC power to FUM
B2 SGND - - Ground
Connector Pin No. Signal I/O Voltage Description
To Next Page
Loading...
