Why is my USB memory not recognized by my Kyocera TASKalfa 400ci?
If your Kyocera All in One Printer is not recognizing the USB memory: * Check that the USB memory is securely plugged into the machine. * If the USB host is blocked, select Unblock in the USB host settings.
Why are printouts from my Kyocera TASKalfa 400ci All in One Printer fuzzy?
If printouts from your Kyocera All in One Printer are fuzzy, and the machine is being used in very humid conditions, carry out Drum Refresh.
Why Kyocera TASKalfa 400ci All in One Printer cannot send document?
If your Kyocera All in One Printer cannot send a document, make sure the modular cord is correctly connected. If a send error is displayed, identify the cause of the error and try sending again. Also, verify whether TX (transmission) restriction is activated and, if so, cancel the TX restriction.
What to do if my Kyocera TASKalfa 400ci has a paper jam?
If a paper jam occurs, the Kyocera All in One Printer will stop, and the location of the jam will be indicated on the touch panel. Leave the machine on and follow the instructions to remove the jammed paper.
Why my Kyocera TASKalfa 400ci cannot print?
There could be several reasons why your Kyocera All in One Printer cannot print: * The power cord might not be plugged into an AC outlet. Plug it in. * The main power switch might not be turned on. Turn it on. * The printer cable might not be connected securely. Connect the correct printer cable securely. * The machine might have been powered on before the printer cable was connected. Power on the machine after connecting the printer cable. * 'Press Status Key...' might be displayed at the top of the screen. Press the Status/Job Cancel key, [Printing Jobs], and then [Resume All Print Jobs] to restart printing.
How to fix light printouts on my Kyocera All in One Printer?
If your Kyocera All in One Printer's printouts are too light, consider the following: * If the machine is in Auto Density mode, set the correct density level for auto density. * If the machine is in Manual Density mode, use [Image Quality] to set the correct density level. * Shake the toner container from side to side several times to evenly distribute the toner. * If there is a message indicating the addition of toner, replace the toner container. * If the paper is damp, replace it with new paper. * Carry out Drum Refresh. * Carry out Developer Refresh. * Carry out Laser Scanner Cleaning. * If EcoPrint mode is enabled, disable it.
Why are the printouts from my Kyocera TASKalfa 400ci All in One Printer dirty?
Dirty printouts from your Kyocera All in One Printer may be due to: * A dirty platen or document processor. Clean them. * A dirty transfer roller. Brush the transfer roller clean. * A dirty drum. Carry out Drum Refresh. * Carry out Developer Refresh. * A dirty scanner. Carry out Laser Scanner Cleaning. * The Printed Document Guard Kit being enabled. Disable the Printed Document Guard Kit.
What to do if Kyocera TASKalfa 400ci All in One Printer says 'Add toner'?
If your Kyocera All in One Printer displays the message 'Add toner,' replace the toner container.
Why is my Kyocera TASKalfa 400ci All in One Printer ejecting blank sheets?
If your Kyocera All in One Printer is ejecting blank sheets, check the following: * When placing originals on the platen, ensure they are face-down and aligned with the original size indicator plates. * When placing originals in the optional document processor, ensure they are face-up.
How to fix dark printouts on my Kyocera TASKalfa 400ci All in One Printer?
If your Kyocera All in One Printer's printouts are too dark: * If the machine is in Auto Density mode, set the correct density level for auto density. * If the machine is in Manual Density mode, use [Image Quality] to set the correct density level.
General| Brand | Kyocera |
|---|---|
| Model | TASKalfa 400ci |
| Category | All in One Printer |
| Language | English |
To Next Page
