MSA SUPREMA - Page 13

REV 0, June 2005 Page 13
Operation Manual SUPREMA
Tables
Table 1-1: Sensors available for connection .................................................................... 17
Table 1-2: Software status ATEX ..................................................................................... 18
Table 1-3: Allowed Software versions TÜV SIL 3............................................................. 18
Table 3-1: Voltage Changeover........................................................................................ 37
Table 4-1: Overview of operator keys .............................................................................. 42
Table 5-1: Allowed Conductor Cross Sections ................................................................ 93
Table 5-2: Cable Specifications ....................................................................................... 94
Table 5-3: Maximum Allowable CAN Bus Length ............................................................. 95
Table 5-4: CAN BUS Bit Rate Settings/* MS = measuring point (input) .......................... 96
Table 5-5: Rack-CAN Node Number................................................................................ 96
Table 5-6: CAN Bus Terminating Resistors ..................................................................... 97
Table 5-7: MGO Module, Configuration of turn-on behaviour and failure behaviour ......... 97
Table 5-8: MAO Module, Configuration of turn-on behaviour and failure behaviour ......... 98
Table 5-9: MCI 10 module configuration ........................................................................ 101
Table 5-10: Types of MPI Modules ................................................................................... 101
Table 5-11: Assignment of the Connection Modules ....................................................... 119
Table 5-12: System Configuration/Maximum Loads ........................................................ 120
Table 5-13: MGO Module/Maximum Loads...................................................................... 120
Table 5-14: CAN Bus Connection Elements.................................................................... 124
Table 5-15: Baud rate at the Central Rack ...................................................................... 127
Table 5-16: Baud rate at the Satellite Rack ..................................................................... 127
Table 5-17: Calculation of the Node ID ............................................................................ 128
Table 5-18: CAN-ID Assignment ...................................................................................... 128
Table 5-19: Technical Data CAN-Bridge CBM ................................................................. 133
Table 5-20: MAT-/MAT-TS Module, Terminal Assignment, Sensor Connections.............. 135
Table 5-21: MGT-40-TS Module, Terminal Assignments for Connection of the Sensors. 136
Table 5-22: MGT-40-TS Module/Allocation MAT – MGT connections............................... 137
Table 5-23: MRO-Module, Contact Load Capacity .......................................................... 138
Table 5-24: MRO-8-Module, Relay Assignment ............................................................... 139
Table 5-25: MRO-8 Module, Terminal Assignment ........................................................... 140
Table 5-26: MRO-8-TS Module, Common Alarm Relay Assignment ............................... 143
Table 5-27: MRO-8-TS-Module, Terminal Assignment .................................................... 143
Table 5-28: MIB Module, System Fail Relay, and Terminal Assignment .......................... 144
Table 5-29: MGT-40-TS Module, Terminal Assignments of the Switching Outputs ......... 146
Table 5-30: MAT-/MAT-TS Module Terminal Assignment, Analogue Outputs ................... 149
Table 5-31: MGT-40-TS-Module Terminal Assignment, Analogue Outputs ...................... 149
Table 5-32: MST Module, Pin Assignment, CAN Bus Ports............................................. 152
Table 5-33: RS 232A Terminal Assignment ..................................................................... 152
Table 5-34: RS 232B, Pin Assignment ............................................................................ 153
Table 5-35: Power Requirement of the Sensors and Cables .......................................... 155
Table 5-36: Power Requirements of the System Modules .............................................. 155
Table 5-37: MSP Module, Terminal Assignment............................................................... 157
Table 6-1: Listing of Node ID.......................................................................................... 167
Table 7-1: MCP, MDA, MGO, MAO Modules, Function Status LED ............................... 201
Table 7-2: MAI Module, Function Status LEDs ............................................................... 202