Panasonic FP7 Series - Page 49

■
Ethernet Communication (SMTP Mail Sending) Instruction
Name
Operatio
n
Unit
Mnemonic Operand Function overview
Page
Mail Text
Setting
−
SMTPcB
DY
(P) S1, S2
Sets the text specified by [S2] into the mail
text of the number specified by [S1].
"P.17-102"
(Note 1)
Mail Text Read −
SMTPcB
RD
(P) S, D
Reads the mail text of the number specified
by [S] to the area specified by [D].
"P.17-105"
(Note 1)
Mail Server
Setting
−
SMTPcS
V
(P)
S1, S2,
S3
Sets the mail transmission server and the
sender to the CPU unit according to the
parameters specified by [S1], [S2], and
[S3].
"P.17-108"
(Note 1)
Destination
Group Setting
−
SMTPcA
DD
(P)
S1, S2,
S3, S4
Sets the destination group name specified
by [S2] and the destination address
specified by [S3] and [S4] to the destination
group number specified by [S1].
"P.17-115"
(Note 1)
Mail
Transmission
Setting
−
SMTPcS
ET
(P)
S1, S2,
S3, S4
Stores the mail transmission settings of
[S1] to [S4] in the mail transmission setting
area.
"P.17-120"
(Note 1)
Logging/Trace
mail setting
−
SMTPcL
OG
(P)
S1, S2,
S3, S4
Stores the logging/trace mail settings of
[S2] to [S4] in the logging/trace transfer
setting area specified by [S1].
"P.17-130"
(Note 1)
Mail Send
Request
−
SMTPcR
EQ
(P) S
Requests transmission of the mail with the
transmission No. specified by [S].
"P.17-135"
(Note 1)
Mail
Transmission
Control
−
SMTPcC
TL
(P) S1, S2
Controls whether to enable, disable, or
cancel the transmission of mail, according
to the specification of the control
description [S2] for control target [S1].
"P.17-139"
(Note 1)
(Note 1) Can be used with CPU units CPS4RE*/CPS3RE*.
■
Ethernet Communication (Ethernet/IP) Instruction
Name
Operatio
n
Unit
Mnemonic Operand Function overview
Page
Information
acquisition of
EtherNet/IP
− ETSTAT (P)
S1, S2,
D
Reads the parameter information or status
information specified by [S1] and [S2], and
stores it in the area starting with [D].
"P.17-142"
(Note 1)
EtherNet/IP
node status
acquisition
instruction
− EIPNDST
S, D1,
D2
Stores the status for the node number
specified by [S] in the device specified by
[D1], and stores the execution result in
[D2].
"P.17-148"
(Note 1)
Cyclic
communication
start request
− EIPSTART S, n, D
Starts the node on which the start request
is made within the maximum node number
specified by [n] from the stop request node
number table specified by [S].
"P.17-180"
(Note 1)
Cyclic
communication
stop request
− EIPSTOP S, n, D
Stops the node on which the stop request
is made within the maximum node number
specified by [n] from the stop request node
number table specified by [S].
"P.17-183"
(Note 1)
1.2 List of High-level Instructions
WUME-FP7CPUPGR-12 1-31