10.3.1 General information..............................................................................................................442
10.3.2 Representation of the contour..............................................................................................443
10.3.3 Creating a new contour ........................................................................................................444
10.3.4 Creating contour elements ...................................................................................................446
10.3.5 Entering the master dimension ............................................................................................452
10.3.6 Changing the contour...........................................................................................................453
10.3.7 Contour call (CYCLE62) - only for G code program.............................................................454
10.3.8 Stock removal (CYCLE952) .................................................................................................455
10.3.9 Stock removal rest (CYCLE952) ..........................................................................................465
10.3.10 Plunge-cutting (CYCLE952).................................................................................................467
10.3.11 Plunge-cutting rest (CYCLE952)..........................................................................................473
10.3.12 Plunge-turning (CYCLE952) ................................................................................................476
10.3.13 Plunge-turning rest (CYCLE952) .........................................................................................482
10.4 Milling ...................................................................................................................................485
10.4.1 Face milling (CYCLE61).......................................................................................................485
10.4.2 Rectangular pocket (POCKET3) ..........................................................................................488
10.4.3 Circular pocket (POCKET4) .................................................................................................498
10.4.4 Rectangular spigot (CYCLE76)............................................................................................507
10.4.5 Circular spigot (CYCLE77)...................................................................................................513
10.4.6 Multi-edge (CYCLE79) .........................................................................................................519
10.4.7 Longitudinal groove (SLOT1) ...............................................................................................524
10.4.8 Circumferential groove (SLOT2) ..........................................................................................533
10.4.9 Open groove (CYCLE899) ...................................................................................................541
10.4.10 Long hole (LONGHOLE) - only for G code program ............................................................551
10.4.11 Thread milling (CYCLE70) ...................................................................................................553
10.4.12 Engraving (CYCLE60)..........................................................................................................557
10.5 Contour milling .....................................................................................................................564
10.5.1 General information..............................................................................................................564
10.5.2 Representation of the contour..............................................................................................564
10.5.3 Creating a new contour ........................................................................................................565
10.5.4 Creating contour elements ...................................................................................................568
10.5.5 Changing the contour...........................................................................................................573
10.5.6 Contour call (CYCLE62) - only for G code program.............................................................574
10.5.7 Path milling (CYCLE72) .......................................................................................................575
10.5.8 Contour pocket/contour spigot (CYCLE63/64).....................................................................581
10.5.9 Predrilling contour pocket (CYCLE64) .................................................................................583
10.5.10 Milling contour pocket (CYCLE63) .......................................................................................587
10.5.11 Contour pocket residual material (CYCLE63, option) ..........................................................593
10.5.12 Milling contour spigot (CYCLE63) ........................................................................................596
10.5.13 Contour spigot residual material (CYCLE63, option) ...........................................................601
10.6 Further cycles and functions ................................................................................................605
10.6.1 Swiveling plane / aligning tool (CYCLE800).........................................................................605
10.6.2 Swiveling tool (CYCLE800)..................................................................................................612
10.6.2.1 Aligning turning tools - only for G code program (CYCLE800) ............................................612
10.6.2.2 Aligning milling tools - only for G code program (CYCLE800) .............................................615
10.6.2.3 Preloading milling tools - only for G code program (CYCLE800).........................................615
10.6.3 High-speed settings (CYCLE832) ........................................................................................617
10.6.3.1 Parameters...........................................................................................................................620
10.6.4 Subroutines ..........................................................................................................................621
10.6.5 Adapt to load (CYCLE782)...................................................................................................623
Table of contents
Turning
16 Operating Manual, 06/2019, A5E44903486B AB
To Next Page
Loading...
