D-Link xStack DGS-3120 Series User Manual

xStack
®
DGS-3120 Series Layer 3 Managed Gigabit Ethernet Switch CLI Reference Guide
125
dst_port_mask - Specify the TCP destination port mask.
<hex 0x0-0xffff> - Enter the TCP source port mask value here.
flag_mask - (Optional) Specify the TCP flag field mask.
all - Specify that the TCP flag field mask will be set to 'all'.
urg - Specify that the TCP flag field mask will be set to 'urg'.
ack - Specify that the TCP flag field mask will be set to 'ack'.
psh - Specify that the TCP flag field mask will be set to 'psh'.
rst - Specify that the TCP flag field mask will be set to 'rst'.
syn - Specify that the TCP flag field mask will be set to 'syn'.
fin - Specify that the TCP flag field mask will be set to 'fin'.
udp - (Optional) Specify that the rule applies to UDP traffic.
src_port_mask - Specify the UDP source port mask.
<hex 0x0-0xffff> - Enter the UDP source port mask value here.
dst_port_mask - Specify the UDP destination port mask.
<hex 0x0-0xffff> - Enter the UDP destination port mask value here.
protocod_id_mask - (Optional) Specify that the rule applies to IP protocol ID traffic.
<hex 0x0-0xff> - Enter the protocol ID mask value here.
user_define_mask - (Optional) Specify that the rule applies to the IP protocol ID, and that the
mask option behind the IP header length is 20 bytes.
<hex 0x0-0xffffffff> - Enter the user-defined mask value here.
ipv6 - (Optional) Specify this is an IPv6 mask.
class - (Optional) Specify the IPv6 class.
source_ipv6_mask - (Optional) Specify an IPv6 source sub-mask.
<ipv6mask> - Enter the IPv6 source sub-mask value here.
destination_ipv6_mask - Specify an IPv6 destination sub-mask.
<ipv6mask> - Enter the IPv6 destination sub-mask value here.
tcp - (Optional) Specify that the following parameter are application to the TCP configuration.
src_port_mask - Specify an IPv6 Layer 4 TCP source port mask.
<hex 0x0-0xffff> - Enter the Ipv6 TCP source port mask value here.
dst_port_mask - Specify an IPv6 Layer 4 TCP destination port mask.
<hex 0x0-0xffff> - Enter the Ipv6 TCP destination port mask value here.
udp - (Optional) Specify that the following parameter are application to the UDP configuration.
src_port_mask - Specify an IPv6 Layer 4 UDP source port mask.
<hex 0x0-0xffff> - Enter the Ipv6 UDP source port mask value here.
dst_port_mask - Specify an IPv6 Layer 4 UDP destination port mask.
<hex 0x0-0xffff> - Enter the Ipv6 UDP destination port mask value here.
icmp - (Optional) Specify that the rule applies to ICMP traffic.
type - Specify the type of ICMP traffic.
code - Specify the code of ICMP traffic.
Restrictions
Only Administrator, Operator and Power-User level users can issue this command.
Example
To create an egress access list profile with the name “eap-eth-bc” and assign the profile ID to be 1:
DGS-3120-24TC:admin# create egress_access_profile profile_id 1 profile_name
eap-eth-bc ethernet source_mac FF-FF-FF-FF-FF-FF
Command: create egress_access_profile profile_id 1 profile_name eap-eth-bc
ethernet source_mac FF-FF-FF-FF-FF-FF
DGS-3120-24TC:admin#

D-Link xStack DGS-3120 Series Specifications

General

MAC Address Table	16K entries
Ports	10/100/1000BASE-T ports
VLANs	4094
Jumbo Frame	Up to 9KB
Power Supply	Internal power supply (depending on model)
Power over Ethernet (PoE)	No
Layer 3 Features	RIP
Quality of Service (QoS)	8 queues per port, DiffServ
Security Features	ACLs
Management	Web-based, CLI, SNMP
Operating Temperature	0°C to 40°C
Storage Temperature	-40°C to 70°C
SFP Ports	Combo 10/100/1000BASE-T/SFP ports and/or dedicated SFP/SFP+ ports (depending on model)