To Next Page

To Previous Page

Chapter 9 Measure Mode – Service Tab

Ethernet

DSAM Help User Guide Rev. 001 227

Network Assignments

The Network Assignment area displays the IP Address, Subnet Mask

and Default Gateway.

Meter Information

The meter information area displays the CPE MAC Address.

Displaying

Throughput

Results

The Throughput view displays Ethernet throughput (upstream and

downstream) test results.

To display the Throughput view

1 Press the View softkey.

2 Using the arrow keys, select Throughput.

3 Press ENTER.

Figure 202 Measure – Bind Results

Network Assignments

Meter Information

Figure 203 Measure Mode – Ethernet

Throughput Graphs

21128026 R001 DSAM Help User Guide.book Page 227 Thursday, February 5, 2009 2:02 PM

Default Chapter7
- Table of Contents7
Table 1 Technical Assistance Centers36
Purpose and Scope36
Assumptions36
Related Information36
Technical Assistance36
Table 2 Typographical Conventions38
Table 3 Keyboard and Menu Conventions38
Conventions38
Table 4 Symbol Conventions39
Table 5 Safety Definitions39
Chapter 1 DSAM Product Family Series Overview41
- DSAM Product Family Series Overview42
- Figure 1 DSAM Product Family Series Field Meter Front Panel Layout42
- Meter Information43
About DSAM Product Family Series42
Figure 2 Meter Info43
Table 6 Obtaining DSAM Information43
Figure 3 DSAM Mode Keys44
Table 7 Shift Key Shortcuts44
Mode Keys44
- Figure 4 Shift Key - Softkey Options45
- Softkey Shortcuts with Function Keys45
Shift Keys44
Table 8 Function Shift Key Shortcuts46
Additional Functions46
Chapter 2 DSAM Navigation47
- DSAM Navigation48
The Keypad48
- Softkeys48
- Exit Key48
- Enter Key48
- Arrow Keys48
- Mode Keys48
- Alphanumeric Keypad48
- Shift Key48
- Power Key49
The User Interface49
- Figure 5 Example: User Interface49
- AC Power50
- Active Channel Plan Name50
- Icons50
Accessing Help50
- Introduction50
- Accessing Help from a Mode Menu51
- Accessing Help from a Submode51
Figure 7 Help Menu for Autotest52
Figure 8 Help Main Menu52
Chapter 3 Battery Installation53
Installing and Maintaining the EZ Charge Battery54
- Installing the Battery54
- Removing the Battery54
- Connecting the Power Components55
  - High Capacity Battery to External Power Connection55
- Figure 9 DSAM Product Family Series Field Meter (Rear View)55
- Figure 10 High Capacity External Power Components56
- Connecting the RF Cable57
Installing and Maintaining the Standard Capacity Battery57
- Installing the Battery57
- Removing the Battery57
- Connecting the Power Components (Standard Capacity Battery)57
Figure 11 Standard Capacity External Power Components58
Making Additional Connections59
Chapter 4 Powering the DSAM61
- Table 10 Battery Charge and Operation Values62
- Understanding the Standard Capacity Battery Led's63
Powering the Meter62
- Charging the Battery62
- Choosing a Power Option62
- Understanding the High Capacity Battery Led's64
Table 12 High Capacity Charge LED Indications65
Chapter 5 Configuring the Meter67
Overview68
- Figure 13 Configure - General Tab: Contrast Adjustment69
- Figure 14 Configure - Adjust Contrast70
- Sound70
  - Configuring Sounds70
- Figure 15 Configure - General Tab: Sounds71
- Figure 16 Configure - Adjust Sounds71
- Battery Conservation72
- About Me74
- Configuring "About Me74
- Diagnostic90
  - Testing the Keypad90
Configure - General Tab68
- Contrast68
  - Configuring Screen Contrast69
Figure 42 Configure - Bind Results93
Figure 43 TPP - DSAM Remote Access93
Figure 44 TPP - JDSU Remote DSAM94
Figure 45 TPP - JDSU Remote DSAM94
Figure 46 Configure - Measure Tab: Sweep Settings95
Configure - Measure Tab95
- Sweep Settings95
- Figure 48 Configure - Measure Tab: Limit Sets98
- Limit Sets98
  - Configuring Limit Sets98
- Table 22 Limit Set Parameters99
- DOCSIS Throughput101
  - Configuring DOCSIS Throughput101
Configure - Channel Plan Tab117
- Overview117
- Figure 68 Configure - Downstream Plans118
- Figure 67 Configure - Channel Plan Tab: Downstream Plans118
- Editing a Channel Plan119
- Table 34 DOCSIS Channel Parameters123
- Configuring Channels for Miniscan124
Configure - Access Tab136
- Location Settings Parameters136
- PC Connection136
- Figure 91 Configure - PC Connection137
- Figure 90 Configure - Access Tab: PC Connection137
- Table 36 PC Connection Parameters138
- WFA Browser Settings138
  - Configuring WFA Browser Settings138
- Figure 93 Configure - Browser Settings139
- Figure 92 Configure - Access Tab: WFA Browser Settings139
- Table 37 WFA Browser Settings Parameters140
- Access Mode141
Chapter 6 Access Mode141
Overview142
- Figure 94 Access - Files Tab: Work Folders142
- Creating a Folder143
  - Figure 96 Access - Open a File143
  - Purging Synchronized Folders144
- Deleting a Folder144
Access - Files Tab142
- Work Folders142
  - Opening a File in Folder142
Access - Browser Tab148
- Overview148
- Figure 103 Access - WFA Browser150
- Graphical Pointer150
- Softkeys150
Figure 106 Access - Browser Tab: WFA Browser154
Chapter 7 Autotest Mode155
Autotest Overview156
- Combo Test156
- Video Channels156
- Home Certification156
- Proof of Performance156
- Cable Modem156
Autotests Tab156
- Figure 109 Autotest - Configure Autotest157
- Running a Combo Test157
- Figure 110 Autotest - Autotest in Progress159
- Understanding Combo Test Results160
- Viewing Combo Test Results160
- Figure 115 Autotest - Video Autotest163
- Figure 116 Autotest - Autotest in Progress164
- Table 41 Home Certification Test Results165
- Understanding Video Channels Results165
- Home Certification Test166
- Figure 134 Autotest - Video Autotest Results181
- Figure 133 Autotest - Proof of Performance181
- Understanding Proof of Performance Results181
- Cable Modem Test182
  - Running a Cable Modem Test182
Figure 137 Autotest - Video Autotest Results185
Figure 138 Autotest - Cable Modem Test: DOCSIS Channel Status187
Chapter 8 Measure Mode – Basic Tab189
Measure Mode - Basic Tab189
Basic Measurement Modes190
- Level190
- Miniscan190
- Full Scan190
- Tilt190
- Constellation190
- Fdr190
- Return QAM Generator190
- QAM Ingress190
- Hum190
- Dqi191
- Return Loopback191
Level191
- Frequency Tuning191
- Channel Tuning192
- Figure 142 Measure Mode - Level193
- Running a Level Measurement193
- Understanding Level Results194
Miniscan198
- Running a Miniscan198
- Channel Status Area200
- Choosing Miniscan Channels200
Full Scan201
- Running a Full Scan201
- Figure 149 Measure Mode - Full Scan Graph202
- Figure 148 Measure Mode - Basic Tab202
- Understanding Full Scan Results (Graph)202
- Channel Status Area203
- Graph203
- Graph Information Bar203
- Measurement Information Area203
- Understanding Full Scan Results (Table)204
- Setting the Full Scan Speed205
- Enabling Channels for Full Scan206
Figure 152 Measure Mode - Enable/Disable Channels207
Tilt208
- Measuring Tilt208
- Understanding Tilt Results210
- Figure 155 Measure Mode - Downstream Plans211
- Figure 156 Measure Mode - Select Tilt Channels212
- Setting High and Low Pilot Channels212
- Viewing Tilt Results213
Constellation214
- Running a Constellation Test214
- Figure 158 Measure Mode - Constellation215
- Figure 157 Measurement Mode - Basic Tab: Constellation215
- Understanding Constellation Results215
  - Measurement Information Area215
- Digital Performance216
- Impairments216
- Figure 160 Constellation - Phase Noise217
- Editing the Channel Plan218
- Gain Compression218
- I/Q Imbalance218
- Setting the Sample Refresh Rate218
Fdr220
- Running an FDR Scan220
- Understanding FDR Results221
- Measurement Information Area222
- Resolution of Measurement222
Return QAM Generator224
- Figure 168 Measure Mode - Basic Tab: Return QAM Generator225
- Changing the Msym/S226
- Understanding Return QAM Generator Results226
  - Measurement Information Area226
- Accessing Other Modes from Return QAM Generator227
- Graph227
Figure 169 Measure Mode - Return QAM Generator226
QAM Ingress227
- Symbol Rate227
- Transmit Status227
- Figure 170 Measure Mode - Basic Tab: QAM Ingress228
- Figure 171 Measure Mode - QAM Ingress228
- Understanding QAM Ingress Results228
- Using QAM Ingress228
- Graph229
- Graph Information Bar229
- Marker Status Area229
- Measurement Information Area229
- Viewing QAM Ingress Results229
Hum Analysis230
- Performing Hum Analysis230
- Figure 173 Measure Mode - Hum Analysis231
- Understanding Hum Analysis Results231
- Editing the Channel Plan232
- Frequency and Hum232
- Measurement Information Area232
- Total Hum232
Figure 172 Measure Mode - Basic Tab: Hum231
Dqi232
- Performing DQI Analysis232
- Figure 174 Measure Mode - Basic Tab: DQI233
- Figure 175 Measure Mode - DQI233
- Understanding DQI Results233
  - Measurement Information Area233
- Changing/Editing the Channel Plan234
- Dqi234
- Graph234
- Graph Information Bar234
- Min234
Return Loopback234
- Viewing DQI Results234
- Figure 176 Measure - Return Loopback235
- Figure 177 Measure Mode - Loopback235
- Performing Return Loopback235
- Enabling/Disabling Transmit236
- Performing a Transmit Reference236
- Setting the Transmit Level236
Reading Measurement Graphs236
- Reading Bar Graphs236
- Reading Line Graphs237
  - White237
Figure 178 Measure Mode - Level Channel237
Saving Results238
- Figure 179 Measure - DQI Results238
- Changing the Default Folder240
- Creating a New Folder240
Chapter 9 Measure Mode – Service Tab243
Measure Mode - Service Tab243
- Figure 183 Measure Mode - Service Tab244
- Configuring DSAM for DOCSIS Tests245
Service Measurement Modes244
Docsis244
- CM Diagnostics Page244
- Ethernet244
- Introduction244
- Voip244
- Figure 184 Configure Mode - Other Settings245
- Running a DOCSIS Test246
- Figure 186 Measure Mode - Cable Modem MAC Address247
- DOCSIS Test Steps249
Ethernet265
- Configuring DSAM for Ethernet Tests265
- Packet Loss Test265
- Ping Test265
- Throughput Test265
- Displaying IP Information266
- Displaying Throughput Results267
- Figure 202 Measure - Bind Results267
- Meter Information267
- Network Assignments267
- Restoring Ping Test Defaults270
Figure 206 Measure Mode - Ethernet Ping Test270
CM Diagnostics Page272
- Testing CM Diagnostics272
  - Navigating the Cable Modem Information System Screen273
Figure 207 Measure Mode - Service Tab: CM Diagnostics273
Figure 208 Measure Mode - Cable Modem Information System273
Voip274
- Configuring DSAM for Voip Tests275
- Figure 209 Measure Mode - Service Tab: Voip275
- Running a Voip Test275
- Accepting a Call280
Figure 224 Measure Mode - Voip Ongoing Call285
Chapter 10 Measure Mode – Spectrum Tab287
Measure Mode - Spectrum Tab287
Spectrum Measurement Modes288
- Downstream Spectrum288
- Field View288
- Ingress Resistance288
- Upstream Spectrum288
- Running an Upstream Spectrum289
- Understanding Upstream Spectrum Results290
Figure 228 Measure - Upstream Spectrum291
Downstream Spectrum292
- Figure 229 Spectrum - Downstream Spectrum293
- Figure 230 Spectrum - Downstream Spectrum293
- Running a Downstream Spectrum293
- Figure 232 Spectrum - Downstream Spectrum294
- Understanding Downstream Spectrum Results295
Field View298
- Figure 236 Measure Mode - Field View299
- Running a Field View299
- Figure 240 Measure Mode - Node Info302
- Understanding Field View Results304
Ingress Resistance306
- Measuring Ingress Resistance306
- Figure 244 Spectrum - Ingress Resistance307
- Understanding Ingress Resistance Results308
Chapter 11 Measure Mode – Sweep Tab311
Measure Mode - Sweep Tab311
Sweep Measurement Modes312
- Forward Sweep312
- Reverse Sweep312
- Sweepless Sweep313
- Reverse Alignment313
Forward Sweep313
- Figure 247 Measure Mode - Sweep Tab313
  - Figure 248 Measure Mode - Sweep Tab314
  - Understanding Forward Sweep Results315
- Running a Forward Sweep314
Reverse Sweep319
- Figure 251 Measure Mode - Sweep Tab320
- Running a Reverse Sweep320
- Understanding Reverse Sweep Results321
Figure 254 Measure Mode - Sweepless Sweep325
Sweepless Sweep325
- Running a Sweepless Sweep325
- Figure 255 Measure Mode - Sweep Tab326
- Understanding Sweepless Sweep Results327
Reverse Alignment330
- Running a Reverse Alignment330
- Graph332
- Graph Information Bar332
- Marker Status Area332
- Measurement Information Area332
- Viewing Reverse Alignment Results332
Appendix A Specifications335
Table 47 Product Specifications336
DSAM Product Family Series-1500, -2500, -2600, -3500, -3600, -6000 Specifications336
Table 48 Power Component Specifications342
Power Component Specifications342
Appendix B Safety Instructions343
Important Safety Instructions344
- Meter Safety344
- Battery Safety345
- Battery Power Supply Module Safety346
Appendix C Customer Services347
About Our Services348
Customer Care348
- Technical Assistance (Business Hour)348
- Instrument Repair349
- Equipment Return Instructions349
- Warranty Information350
Global Services and Solutions352
- System Deployment and Field Engineering353
- Training353
  - Instructor-Led Training353
    - On-Site Training (Customer Site)353
    - Public Courses (JDS Uniphase Corporation Sites)353
  - Alternative Learning354
    - Computer-Based Training (CBT)354
    - Courseware Licensing Program and Train-The-Trainer354
- Product Support355
- Consulting Services355
Glossary357

Brand	JDS Uniphase
Model	DSAM-3600
Category	Measuring Instruments
Language	English

JDS Uniphase DSAM-3600 User Manual

Table of Contents

Questions and Answers:

JDS Uniphase DSAM-3600 Specifications

Related product manuals