Sequencer mode
116
3: S–TRACK (Track Parameters)
3–1: MIDI
Here you can adjust MIDI-related settings for each MIDI track.
Track 01...16 (Track Number)
To select a track, place the cursor at one of the following
parameters, and use the cursor buttons to switch tracks.
(see
page 105)
MIDI Channel [01…16]
Specifies the MIDI channel that the MIDI track will use to
transmit and receive musical data. The MIDI channel you specify
here will be the receive channel when Status is INT, the transmit
channel when it is EXT or EX2, and the receive/transmit channel
when it is BTH. Tracks set to INT which have the same MIDI
channel will sound and be controlled identically when they receive
MIDI data or data from the sequencer tracks.
Bank Select MSB (When Status=EX2) [000...127]
Bank Select LSB (When Status=EX2) [000...127]
When Status is set to EX2, this sets the bank number that will be
transmitted. When Status is other than EX2, this setting has no
effect.
Track Info.
Shows the settings of tracks 1–16 for the parameter that you're
editing.
Note: If this is disabled because of the setting of another
parameter, “–” is shown.
3–2: OSC
These parameters specify how each MIDI track will be sounded.
Track 01...16 (Track Number)
To select a track, place the cursor at one of the following
parameters, and use the cursor buttons to switch tracks. (see
page 105)
Force OSC Mode [PRG, Poly, Mono, Legato]
This lets you override the Program’s stored Voice Assign Mode
settings, if desired.
PRG: The Program’s stored P–BASIC> VOICE Voice Assign
Mode settings will be used.
Poly: The track will play polyphonically, regardless of the
Program’s settings.
Mono: The track will play monophonically, regardless of the
Program’s settings.
Legato: The track program will sound monophonically, and will
play legato according to the Program’s Mode setting (P–BASIC>
VOICE).
With the MN or LGT settings, the Program’s Priority setting (P–
BASIC> VOICE) will determine the priority of the note that
sounds when you play two or more notes.
OSC Select [OSC1 & 2, only OSC1, only OSC2]
Specifies whether the MIDI track’s program will play OSC1,
OSC2, or both.
For programs whose OSC(P–BASIC> VOICE) is Double, this
setting lets you specify that only OSC1 or OSC2 will sound.
OSC1 & 2: OSC1 and 2 will sound as specified by the settings of
the program.
only OSC1: Only OSC1 will sound.
only OSC2: Only OSC2 will sound. PCM programs will not
sound if Oscillator Mode is set to Single or Drums.
Portamento [PRG, Off, 001...127]
Create portamento settings for each MIDI track.
PRG: Portamento will be applied as specified by the program
settings.
Off: Portamento will be off, even if the original program settings
specified Portamento to be on.
001…127: Portamento will be applied with the portamento time
you specify here even if it is turned off by the program settings.
The portamento setting you make here will be used when the song
is played or recorded from the beginning. If you change the setting
while recording, it will be recorded as part of the musical data.
(However if you set this to PRG, it will not be recorded.) You can
change this setting during playback. However if you play back any
Portamento On/Off data or Portamento Time data that was
previously recorded, the settings will change accordingly.
When the track where the Status (SEQ> PROG) is INT or BTH,
MIDI control change CC#05 (Portamento Time) and CC#65
(Portamento Switch) can be received to control this and change the
setting. (If the setting is PRG, CC#05 Portamento Time will not be
received.)
When you switch songs or return to the beginning of the song,
tracks where the Status is BTH, EXT, or EX2 will transmit this
setting via MIDI. If this is Off, CC#65 with a value of 0 will be
To Next Page
Loading...
