Sequencer mode
132
10: S–FX ROUTING (Effect Routing)
You can also specify the bus routing for the program used by each
MIDI track 1–16. For instance, you can:
• Send the output of a track to an insert effect
• Route a sound to an insert effect
• Create detailed settings for insert effects
For details on Insert Effects, please see “Effect Guide” on
page 207.
10–1: BUS
Specifies the bus where the program oscillator(s) used by MIDI
tracks 1–16 will be sent. You can also set the send levels to the
master effects from this page.
Routing Map
This area shows the insert effect routing (Bus Select), the name of
the assigned effect, the on/off status, chaining, and the output bus
that follows the insert effect. The type of insert effect, the on/off
status, and the chain settings can be edited in the S–FX
ROUTING> IFX page.
Track 01...16 (Track Number)
To select a track, place the cursor at one of the following parame-
ters, and use the cursor buttons to switch tracks. (see page
105)
Bus (Bus Select) [DKit, L/R, IFX1...5, Off]
This specifies the output bus for the track program’s oscillator(s).
L/R: Output to the L/R bus.
IFX1, 2, 3, 4, 5: Output to the IFX1–5 buses.
Off: The track will not be output from the L/R bus, or IFX1–5
buses. Choose the Off setting if you want the program’s oscillator
output of the track to be connected in series to a master effect. Use
SEND page Send1 (to MFX1) and Send2 (to MFX2) to specify
the send levels.
Tip: You can create a wide variety of routings by using each
track’s Bus Select and the Chain to and Chain settings (SEQ>
MIX) that follow the insert effect.
DKit: You can select this only if the specified program is a drum
program (OSC: Drums).
The Bus Select, FX Control Bus, Send1, and Send2 settings
(GLOBAL DRUM KIT> VOICE) for each key of the selected
drum kit will be used. Check this setting if you want to apply an
individual insert effect to each drum instrument.
Tip: In most preloaded drumkits, the drum instruments have the
same Bus Select settings according to their type, as follows.
Snares → IFX1
Kicks → IFX2
Cymbals → IFX3
Tam, percussions, and others → IFX4
If you want to edit these routings, use the DKit IFX Patch
function. For more information, please see “DKit IFX Patch” on
page 96.
10–2: SEND
Track 01...16 (Track Number)
To select a track, place the cursor at one of the following
parameters, and use the cursor buttons to switch tracks. (see
page 105)
FX Control Bus [Off, FC1, FC2]
Sends the output of the track to an FX Control bus (two-channel
mono FX Ctrl 1 or 2).
Use the FX Control busses when you want a separate sound to
control the audio input of an effect. You can use two FX Control
busses (each is a two-channel mono bus) to control effects in
various ways.
For more information, please see the “FX Control Bus” section on
page 209.
Send1 (MFX1) [000...127]
Send2 (MFX2) [000...127]
For each track, these parameters set the send level to master effects
1 and 2. These settings are valid when Bus Select is set to L/R or
Off. When IFX 1–5 are selected, the send levels to master effects 1
and 2 are set by the Send1 and Send2 parameters of the IFX page,
and are applied after the sound has passed through IFX1–5.
The Send 1 and 2 settings you specify here are used during
playback or recording from the beginning of the song. If you
modify these settings during recording, your changes will be
recorded as performance data; the send amounts will change
accordingly during playback. You can also modify these settings
during playback. However if Send 1 and 2 data has been recorded,
the settings will change according to the recorded data.
If Bus Select is set to IFX1–5, this setting is ignored.
If
Status
(SEQ> PROG) is either INT or BTH, CC#93 and CC
#91 can control send 1 and 2 respectively and change their
settings. When you switch songs or return to the beginning of a
song, tracks where the
Status
is EXT, EX2 or BTH will
transmit these settings via MIDI. This data will be transmitted
on the MIDI channel of each track as set by
MIDI Channel
(S–TRACK> MIDI). The actual send level is determined by
multiplying the value of these parameters with the send level
settings of the program used by the track (
Send1
and
Send2
,
P–FX ROUTING> SEND). (See G–MIDI> OUT: SEQ Mode
“Track MIDI Out” on page 162)
Track Info.
Shows the settings of tracks 1–16 for the parameter that you're
editing.
Note: If this is disabled because of the setting of another
parameter, “–” is shown.
To Next Page
Loading...
