Single size effects 103: St.BPMAutoPanDly (Stereo BPM Auto Panning Delay)
275
104: Tape Echo BPM
This is a tape echo that lets you synchronize the delay time to the
tempo of the song.
L Dly Note Base Note ...3
Selects the type of
notes to specify the
left channel delay
time p.272
Times L Times x1...x32
Sets the number of
notes to specify the
left channel delay
time p.272
Feedbck LFeedback –100...+100
Sets the feedback
amount for the left
channel
R Dly Note Base Note ...3
Selects the type of
notes to specify the
right channel delay
time p.272
Times R Times x1...x32
Sets the number of
notes to specify the
right channel delay
time p.272
Feedbck R Feedback –100...+100
Sets the feedback
amount for the right
channel
Hi Damp[%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range p.266
Lo Damp[%]
Low Damp
[%]
0...100
Sets the damping
amount in the low
range p.266
LFO
LFO
Waveform
Tri (Triangle),
Sine
Selects the LFO
Waveform
Shape LFO Shape –100...+100
Changes the
curvature of the LFO
Waveform p.224
Phase Phase [deg] –180...+180
Sets the LFO phase
difference between
the left and right
p.238
Pan [Hz]
Panning Freq
[Hz]
0.02...20.00
Sets the panning
speed p.223
Pan MDI
Sync
Panning
BPM/MIDI
Sync
Off, On
When this is on, the
pan LFO speed is set
by BPM, Base Note,
and Times, instead of
Frequency p.223
BPM ←
MIDI,
40.00...
300.00
MIDI syncs to the
system tempo; 40–
300 sets the tempo
manually for this
individual effect p.223
Base Note ← ...3
Selects the type of
notes to specify the
delay time for the
panning speed p.223
Times ← x1...x32
Sets the number of
notes to specify the
delay time for the
panning speed p.223
Pan Dept h 0...100
Sets the panning
width
Src Source Off...Tempo
Selects the
modula
tion source
for the panning width
Amt Amount –100...+100
Set the modulation
amount of the
panning width
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Paramter Value Explanation
BPM Delay BPM
MIDI,
40.00...
300.00
MIDI syncs to the
system tempo; 40–
300 sets the tempo
manually for this
individual effect p.272
Tap1 Dmod
Src
Tap1 Dmod
Source
Off...Tempo
Selects the
modulation source of
the delay time p.276
Ta1 Note
Tap1
Delay Note
...3
Selects the type of
notes to specify the
delay time (tap1)
p.272, p.276
Times Tap1 Times x1...x32
Sets the number of
notes to specify the
delay time (tap1)
p.272, p.276
Time Over? ← ---, OVER!
Displays an error
message when the
delay time exceeds
the upper limit p.276
Tap1 Dmod
Dmod Max
Note
...3
Selects the note value
used to specify the
delay time when the
modulation is at
maximum p.276
Times ← x1...x32
Specifies the number
of notes used to
specify the delay time
when the modulation
is at maximum p.276
Tap2 [%]
Tap2
Position [%]
0...100
Sets the position of
Tap 2 relative to the
Tap 1 delay time the
depth of pitch
variation p.270
Tap3 [%]
Tap3
Position [%]
0...100
Sets the position of
Tap 3 relative to the
Tap 1 delay time the
depth of pitch
variation p.270
Feedback
Feedback
Level
0...100
Sets the amount of
feedback for Taps 1, 2,
and 3 p.270
Src Source Off...Tempo
Selects the
modulation source of
feedback amount
Amt Amount –100...+100
Sets the depth by
which feedback
amount will be
modulated
Saturation ← 0...100
Sets the distortion
amount
Hi Damp[%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range
Lo Damp[%]
Low Damp
[%]
0...100
Sets the damping
amoun
t in the low
range
Tap1 Lvl Tap1 Level 0...100
Sets the Tap1 output
level
Pan ← L, 1...99, R
Sets the stereo image
of tap1
FB Amt
Feedback
Amount
–100...+100
Sets the Tap1
feedback amount
p.270
Tap2 Lvl Level 0...100
Sets the Tap2 output
level
Wah Flatter
D
-mod
Tap2/3 Position
+
Tape
Saturation
Left
Right
Wet / Dry
Trim
PanLevel
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Feedback
Feedback Amt
High / Low DampPre Tone
Delay
(1)
(2)
(3)
Delay Time
BPM
BPM
Base Note x Times
Tempo
To Next Page
Loading...
