Effect Guide
220
Threshold
Attack
Release
“Threshold” specifies the level where gating occurs when
“Envelope Select” is set to L/R Mix, L Only, or R Only.
“Attack” and “Release” specify the attack time and release time of
the gate.
Polarity
This inverts the polarity of the gate on/off functionality. With the
“–” setting, the gate will close when the input signal exceeds the
specified level. The direction in which the modulation source
opens or closes the gate will also be reversed.
Delay Time [ms]
This sets the delay time for the input to the gate. When using
shorter Attack Time settings, you can lengthen the Delay Time so
that the sound is input after the gate opens.
007: St.
Parametric
4EQ
(Stereo
Parametric 4EQ)
This is a stereo 4-band parametric equalizer. You can select
peaking type or shelving type for Band 1 and 4. The gain of Band
2 can be controlled by dynamic modulation.
Band1 Type
Band4 Type
Selects a filter type for Band 1 and 4.
Side PEQ
Side PEQ
Insert
Off, On
Switches the trigger
signal equalizer on/
off p.219
Trigger
Monitor
Side PEQ
Trigger
Monitor
Off, On
Switches between
monitoring the effect
output and the
trigger signal p.219
S.PEQ [Hz]
Side PEQ
Cutoff [Hz]
20...12.00k
Sets the center
frequency of the
equalizer for the
trigger signal p.219
Q Side PEQ Q 0.5...10.0
Sets the bandwidth of
the equalizer for the
trigger signal p.219
Gain [dB]
Side PEQ
Gain [dB]
–18.0...+18.0
Sets the gain of the
equalizer for the
trigger signal p.219
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Input Level
Output Level
Threshold
Louder
Louder
Threshold
Attack=1
Release=1
Attack=100
Release=100
Dry
Wet
Wet
Attack
Release
Gate - Attack / Release
Gate - Threshold
Paramter Value Explanation
B1 Fc [Hz]
Band1
Cutoff [Hz]
20...1.00k
Sets the center
frequency of Band 1
Q Band1 Q 0.5...10.0
Sets the bandwidth of
Band 1 p.221
Gain[dB]
Band1
Gain [dB]
–18.0...+18.0
Sets the gain of Band
1
B2 Fc[Hz]
Band2
Cutoff [Hz]
50...10.00k
Sets the center
frequency of Band 2
Q Band2 Q 0.5...10.0
Sets the bandwidth of
Band 2 p.221
Gain[dB]
Band2
Gain [dB]
–18.0...+18.0
Sets the gain of Band
2
B3 Fc[Hz]
Band3
Cutoff [Hz]
300...10.00k
Sets the center
frequency of Band 3
Q Band3 Q 0.5...10.0
Sets the bandwidth of
Band 3 p.221
Gain[dB]
Band3
Gain [dB]
–18.0...+18.0
Sets the gain of Band
3
B4 Fc[Hz]
Band4
Cutoff [Hz]
500...20.00k
Sets the center
frequency of Band 4
Q Band4 Q 0.5...10.0
Sets the bandwidth of
Band 4 p.221
Gain[dB]
Band4
Gain [dB]
–18.0...+18.0
Sets the gain of Band
4
Trim 0...100 Sets the input level
B1Type Band1 Type
Peaking,
Shelf-L
(Shelving-
Low)
Selects the type of
Band 1 p.220
B4Type Band4 Type
Peaking,
Shelf-H
(Shelving-
High)
Selects the type of
Band 4 p.220
B2 Gain Src
Band2
Dynamic
Gain Source
Off...Tempo
Selects the
modulation source of
the Band 2 gain p.221
Amt [dB] Amount [dB] –18.0...+18.0
Sets the modulation
amount of Band 2
gain p.221
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Band1 Band2 Band3 Band4
PEQ PEQ PEQ PEQ
LEQ
LEQ
HEQ
HEQ
PEQ PEQ PEQ PEQ
Trim
Trim
D
-mod
To Next Page
Loading...
