Korg KROSS - Scale

Sequencer mode
118
3–4: SCALE
Here you can adjust the settings for the scale for each MIDI track.
Scale Type (Song’s Scale) [
[Equal Temperament...User Octave Scale15]
Selects the scale.
Key [C…B]
Random [0…7]
As this value is increased, an increasingly random deviation will
be added to the pitch at each note-on.
If Status (SEQ> PROG) is INT, this setting will affect the
pitch produced by the KROSS. If Status is EXT, this setting
will affect the note number of the note messages transmitted
via MIDI.
Track 01...16 (Track Number)
To select a track, place the cursor at one of the following
parameters, and use the cursor buttons   to switch tracks. (see
page 105)
Use Program’s Scale [Off, On]
MIDI tracks can use the scale that is specified by Scale (P–
BASIC> SCALE).
On (checked): The scale specified by the program will be used.
Off (unchecked): The scale specified by Scale will be used.
Track Info.
Shows the settings of tracks 1–16 for the parameter that you're
editing.
If this is disabled because of the setting of another parameter, “–”
is shown.
V 3–1...4: FUNCTION
•0: Memory Status see page 137
•1: Solo Setting see page 63
•2: Undo see page 137
•3: Create New Song see page 137
•4: Rename Song see page 137
•5: Delete Song see page 137
•6: Copy From Song see page 137
•7:
Copy from Combination see page 138
•8: Copy from Program see page 139
•9: Load Template Song see page 139
• 10: Save Template Song (Save as User Template Song) see
page 140
• 11: GM Initialize see page 141
• 12: FF/REW Speed see page 142
• 13: Detune BPM Adjust see page 142
• 14: Set Location (Set Location for Locate Key) see page
142
For more information, please see the “Sequencer: FUNCTION”
section on page 137.
4: S–ZONE /DELAY (Zones/Delay)
4–1: KEY ZONE (Keyboard Zones)
Here you can specify the key zones where MIDI tracks 1–16 will
sound.
The top/bottom key settings specify the zone where MIDI tracks
1–16 will sound, and the top/bottom slope settings specify the key
range where the volume will change starting from the top/bottom
key.
For more information, please see the “4–1: KEY ZONE
(Keyboard Zones)” section on page 118.
These settings do not affect MIDI transmission/reception. All
note data that is received will be recorded into the internal
sequencer, and all note data from the internal sequencer or
from the keyboard will be transmitted.
Zone Map
This area indicates the note and velocity ranges where each MIDI
track (1–16) will sound.
A line indicates the range of notes that will sound, and the slope
within that range is shaded.
Track 01...16 (Track Number)
To select a track, place the cursor at one of the following
parameters, and use the cursor buttons   to switch tracks. (see
page 105)
Top Key [C–1...G9]
Specifies the top key (upper limit) of the notes that will sound for
each MIDI track.
Top Slope [00, 01, 02, 03, 04, 06, 08, 10,
12, 18, 24, 30, 36, 48, 60, 72]
Specifies the range of keys (12 is one octave) where the volume
will be reached starting from the top key.
0: The volume will be at the original level from the top key.
12: The volume will increase gradually as you play downward,
and will reach the original volume one octave below the top key.
72: The volume will increase gradually as you play downward,
and will reach the original volume six octaves below the top key.
Bottom Slope [00, 01, 02, 03, 04, 06, 08, 10,
12, 18, 24, 30, 36, 48, 60, 72]
Specifies the range of keys (12 is one octave) where the volume
will be reached starting from the bottom key.
0: The volume will be at the original level from the bottom key.
12: The volume will increase gradually as you play upward, and
will reach the original volume one octave above the bottom key.
72: The volume will increase gradually as you play upward, and
will reach the original volume six octaves above the bottom key.
Bottom Key [C–1...G9]
Specifies the bottom key (lower limit) of the notes that will sound
for each MIDI track.
Track 1
Track 16
C–1
G9
Bottom Key
Bottom Slope
Top Slope
Top Key