Korg KROSS - D08: St. MIC + Preamp (Stereo MIC Modeling + Preamp)

Effect Guide
286
Amp Type
Cabinet Type
Recommended Combinations of Bass Amp Models and
Cabinets:
D08: St. Mic + PreAmp ( Stereo Mic
Modeling + PreAmp)
This is a stereo mic and preamp simulator (See “028: Mic
Model+PreAmp (Mic Modeling + PreAmp)” on page 234.). For
example you might use this to simulate micing of a stereo source
such as a rotary speaker.
D09: Vocoder
This effect modifies the input signal (carrier) by giving it the tonal
character of a different signal (the modulation). The most popular
way to use this is to input a vocal signal from a connected mic as
the modulator, creating the impression that the musical instrument
is speaking. You can also obtain distinctive effects by using
rhythm or sound effects. The most appropriate choice of carrier is
a sound that contains numerous overtones, such as strings or
distorted guitar.
Formant Shift
By offsetting the Carrier filter, you can adjust the height of the
frequency range where the vocoder effect is applied. The tonal
quality will change significantly.
CarrierNoise Level
This parameter enables you to mix white noise with the Carrier.
Mod. High Mix
This parameter sets the high-range output level of the modulator
sound. If the modulator is a human voice, it will make the words
more clear.
Amp Type Cabinet Type
STUDIO COMBO STUDIO - 1x15
VOX AC100 VOX AC100 - 2x15
UK MAJOR UK - 4x15, UK - 4x12
Tube Pre AmpMic Simulation
Tube Pre AmpMic Simulation
Left
Right
Wet / Dry
Output Level
Wet / Dry
Stereo In - Stereo Out
Paramter Value Explanation
Carrier Trim ← 0...100
Sets the Carrier input
level
Modulator
Trim
← 0...100
Sets the Modulator
input level
Mod Src Mod Source
Input,
FX Control 1,
FX Control 2
Selects the modulator
input
Mod. Select ←
L/R Mix,
L Only,
R Only
Selects whether to
use the left/right mix,
only left, or only right
of the modulator
input
FormntSft
Formant
Shift
–2...+2
Sets the height of the
frequency for the
vocoder effect p.286
Response ← 0...100
Sets the speed of the
response to the
modulator input
CarrirNoise
Carrier Noise
Level
0...100
Sets the noise mix
level to the Carrier
p.286
Src Source Off...Tempo
Selects the
modulation source
for the noise mix level
Amt Amount –100...+100
Sets the modulation
amount for the noise
mix level
Mod. Hi Mix
Mod. High
Mix
0...100
Sets the high-range
output level of the
modulator p.286
LowGain[dB]
Low Gain
[dB]
–12...+12
Sets the low-range
output level of the
vocoder
HiGain[dB]
High Gain
[dB]
–12...+12
Sets the high-range
output level of the
vocoder
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Stereo In - Mono Out / Dry: Stereo In - Stereo Out
Band Pass Filter
Envelope
Carrier Trim
Modulator Trim
Modulator High Mix
Noise
Generator
Noise Level
+
+
FX Control BUS 1
FX Control BUS 2
Modulator Source
Modulator Select
+
+