3: C–TIMBRE (Timbre Parameters) 3–1: MIDI
77
3: C–TIMBRE (Timbre Parameters)
3–1: MIDI
Here you can adjust MIDI settings for timbres 1–16.
Timbre 01...16 (Timbre Number)
To select a timbre (active timbre), place the cursor at one of the
following parameters, and use the cursor buttons to switch
timbres.(see page 71)
MIDI Channel [01...16, Gch]
Sets the MIDI transmit/receive channel for each timbre.
Gch: The timbre will use the channel that has been selected as the
global MIDI Channel (G–MIDI> BASIC).
When Status is INT, MIDI messages will be received on the
channel you specify here. If this setting is the same as the global
MIDI channel, the internal tone generator will sound according to
the internal settings. If this is set to EXT or EX2, playing the
KROSS will transmit MIDI messages on the MIDI channel
specified here. (Messages will also be transmitted simultaneously
on the global MIDI channel.)
Bank Select (When Status = EX2) MSB [000...127]
Bank Select (When Status = EX2) LSB [000...127]
Specifies the bank number that will be transmitted when Status is
set to EX2. The upper line is the MSB, and the lower line is the
LSB. This setting has no effect if Status is other than EX2.
Timbre Info.
Shows the settings of timbres 1–16 for the parameter that you're
editing.
Soloed timbres are indicated by (S).
3–2: OSC
These settings specify how timbres 1––16 will be played.
Timbre 01...16 (Timbre Number)
To select a timbre (active timbre), place the cursor at one of the
following parameters, and use the cursor buttons to switch
timbres.(see page 71)
Force OSC Mode [PRG, Poly, Mono, Legato]
This lets you override the Program’s stored Voice Assign Mode
settings, if desired.
PRG: The mode will be according to the Voice (Voice Assign
Mode) setting in the program's P-BASIC> VOICE page.
Poly: The timbre will play polyphonically, regardless of the
Program’s settings.
Mono: The timbre will play monophonically, regardless of the
Program’s settings.
Legato: The timbre will sound monophonically, and will play
legato according to the Program’s VOICE setting.
With the Mono or Legato settings, the Program’s Priority setting
(P–BASIC> VOICE) will determine the priority of the note that
sounds when you play two or more notes.
OSC Select [OSC1&2, only OSC1, only OSC2]
Specifies whether the timbre’s program will play OSC1, OSC2, or
both.
For programs whose Oscillator Mode (P–BASIC> VOICE) is
Double, this setting lets you specify that only OSC1 or OSC2 will
sound.
OSC1&2: OSC1 and 2 will sound as specified by the settings of
the program.
only OSC1: Only OSC1 will sound.
only OSC2: Only OSC2 will sound. Programs will not sound if
Oscillator Mode is set to Single or Drums.
Portamento [PRG, Off, 001...127]
Create portamento settings for each timbre.
PRG: Portamento will be applied as specified by the program
settings.
Off: Portamento will be off, even if the original program settings
specified Portamento to be on.
001…127: Portamento will be applied with the portamento time
you specify here even if it is turned off by the program settings.
If the Status (COMBI> PROG) is set to INT, CC#05
(portamento time) and CC#65 (portamento switch) messages
will be received and will control and change these settings.
(If the setting is PRG, CC#05, portamento time will not be
received.) These messages will be received on the MIDI
channel specified for each timbre by MIDI Channel (C–
TIMBRE> MIDI).
Timbre Info.
Shows the settings of timbres 1–16 for the parameter that you're
editing.
Soloed timbres are indicated by (S).
To Next Page
Loading...
Need help?
General
