Korg KROSS - Limiter - P4 EQ (Limiter - Parametric 4-Band EQ)

Effect Guide
246
051: Limiter - P4EQ (Limiter -
Parametric 4-Band EQ)
This effect combines a mono limiter and a four-band parametric
equalizer. You can change the order of the effects.
052: Limiter - Phaser
This effect combines a mono limiter and a phaser. You can change
the order of the effects.
Paramter Value Explanation
Limiter
L Ratio Ratio
1.0 : 1...
50.0 : 1, Inf : 1
Sets the signal
compression ratio
p.218
Thrsh[dB]
Threshold
[dB]
–40...0
Sets the level above
which the
compressor is applied
p.218
L Attack Attack 1...100 Sets the attack time
Release ← 1...100 Sets the release time
L Gain [dB]
Gain Adjust
[dB]
–Inf,
–38...+24
Sets the limiter
output gain p.218
Parametric 4-Band EQ
E Trim Trim 0...100
Sets the parametric
EQ input level
E B1 F[Hz]
Band1
Cutoff [Hz]
20...1.00k
Sets the center
frequency of Band 1
Q Band1 Q 0.5...10.0
Sets the bandwidth of
Band 1 p.221
Gain [dB]
Band1
Gain [dB]
–18...+18 Sets the gain of Band 1
E B2 F[Hz]
Band2
Cutoff [Hz]
50...5.00k
Sets the center
frequency of Band 2
Q Band2 Q 0.5...10.0
Sets the bandwidth of
Band 2 p.221
Gain [dB]
Band2
Gain [dB]
–18...+18 Sets the gain of Band 2
E B3 F[Hz]
Band3
Cutoff [Hz]
300...10.00k
Sets the center
frequency of Band 3
Q Band3 Q 0.5...10.0
Sets the bandwidth of
Band 3 p.221
Gain [dB]
Band3
Gain [dB]
–18...+18 Sets the gain of Band 3
E B4 F[Hz]
Band4
Cutoff [Hz]
500...20.00k
Sets the center
frequency of Band 4
Q Band4 Q 0.5...10.0
Sets the bandwidth of
Band 4 p.221
Gain [dB]
Band4
Gain [dB]
–18...+18 Sets the gain of Band 4
Routing ←
Limiter →
PEQ,
PEQ →
Limiter
Switches the order of
the limiter and
parametric EQ
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
S
rc Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Limiter
Trim
Parametric 4Band EQ
Limiter
Gain Adjust
Envelope - Control
Paramter Value Explanation
Limiter
L Ratio Ratio
1.0 : 1...
50.0 : 1, Inf : 1
Sets the signal
compression ratio
p.218
Thrsh[dB]
Threshold
[dB]
–40...0
Sets the level above
which the
compressor is applied
p.218
L Attack Attack 1...100 Sets the attack time
Release ← 1...100 Sets the release time
L Gain [dB]
Gain Adjust
[dB]
–Inf,
–38...+24
Sets the limiter
output gain p.218
Phaser
P LFO [Hz]
LFO Freq
[Hz]
0.02...20.00
Sets the speed of the
LFO
LFO
LFO
Waveform
Tri (Triangle),
Sine
Selects the LFO
Waveform
Depth ← 0...100
Sets the depth of LFO
modulation
Manual ← 0...100
Sets the frequency
where the effect is
applied
Reso Resonance –100...+100
Sets the resonance
amount p.235
P Wet/Dry
[Phaser]
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the phaser effect
balance p.226, p.235
Src
[Phaser]
Source
Off...Tempo
Selects the phaser’s
Wet/Dry modulation
source
Amt
[Phaser]
Amount
–100...+100
Sets the phaser’s Wet/
Dry modulation
amount
P Out
Output
Mode
Normal,
Wet Invert
Selects the phaser
output mode p.253
Routing ←
Limiter →
Phaser,
Phaser →
Limiter
Switches the order of
the limiter and phaser
p.263
Wet/Dry ←
–Wet...
–99 : 1, Dry,
99 : 1...Wet
Sets the balance
between the effect
and the dr
y input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Limiter
Limiter
Gain Adjust
Envelope - Control
Phaser
Phaser
Resonance
LFO: Tri / Sine
Phaser Wet / Dry
Normal
Wet Invert
Output Mode
–
+