Effect Guide
254
067: St.HarmonicChorus (Stereo
Harmonic Chorus)
This effect applies chorus only to the higher frequencies. This can
be used to apply a chorus effect to a bass sound without making
the sound thinner. You can also use this chorus block with
feedback as a flanger.
High/Low Split
This parameter sets the frequency that splits the high and low
range. Only the high range will be sent to the chorus block.
Feedback
Sets the feedback amount of the chorus block. Increasing the
feedback will allow you to use the effect as a flanger.
068: St.
Biphase Mod. (Stereo Biphase
Modulation)
This stereo chorus effect adds two different LFOs together. You
can set the Frequency and Depth parameters for each LFO
individually. Depending on the setting of these LFOs, very
complex waveforms will create an analog-type, unstable
modulated sound.
Paramter Value Explanation
LFO
LFO
Waveform
Tri (Triangle),
Sine
Selects the LFO
Waveform
LFO Phase
[deg]
← –180...+180
Sets the LFO phase
difference between
the left and right
p.226
LFO [Hz]
LFO Freq
[Hz]
0.02...20.00
Sets the speed of the
LFO p.226
Src Source Off...Tempo
Selects a modulation
source for LFO speed
Amt Amount
–20.00...
+20.00
Sets the modulation
amount of LFO speed
MIDI Sync
BPM/MIDI
Sync
Off, On
When this is on, the
LFO speed is set by
BPM, Base Note, and
Times, instead of
Frequency
p.223
BPM ←
MIDI,
40.00...
300.00
MIDI syncs to the
system tempo; 40–
300 sets the tempo
manually for this
individual effect p.223
Base Note ← ...
Selects the type of
notes that specify the
LFO speed p.223
Times ← x1...x32
Sets the number of
notes that specify the
LFO speed p.223
Depth ← 0...100
Sets the depth of LFO
modulation
Delay[ms]
Pre Delay
[ms]
0.0...50.0
Sets the delay time
from the original
sound
Feedback ← –100...+100
Sets the feed back
amount of the chorus
block p.255
HiDamp [%]
High Damp
[%]
0...100
Sets the high range
damping amount of
the chorus block
Hi/Lo Split
High/Low
Split
1...100
Sets the frequency
split point between
the low and high
range p.254
Low Level ← 0...100
Sets the low range
output level
High Level ← 0...100
Sets the high range
(chorus) output level
Wet/Dry ←
Dry, 1 : 99...
99
: 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Feedback
LFO Phase
LFO: Tri / Sine
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
Low Level
Low Level
High Level
High Level
High/Low Split Point
High Damp
Chorus/Flanger
Chorus/Flanger
Paramter Value Explanation
LFO1
LFO1
Waveform
Tri (Triangle),
Sine
Selects LFO1
waveform
LFO2
LFO2
Waveform
Tri (Triangle),
Sine
Selects LFO2
waveform
Phase Phase Sw 0 , 180(deg)
Switches the LFO
phase difference
between left and
right
LFO1[Hz]
LFO1 Freq
[Hz]
0.02...30.00 Sets the LFO1 speed
Src Source Off...Tempo
Selects the
modulation source of
LFO1&2 speed
Amt Amount
–30.00...
+30.00
Sets the modulation
amount of LFO1
speed
LFO2[Hz]
LFO2 Freq
[Hz]
0.02...30.00 Sets the LFO2 speed
Amt Amount
–30.00...
+30.00
Sets the modulation
amount of LFO2
speed
Depth1 ← 0...100
Sets the depth of
LFO1 modulation
Depth2 ← 0...100
Sets the depth of
LFO2 modulation
L Dly[ms]
L Pre Delay
[ms]
0.0...50.0
Sets the delay time
for the left channel
p.253
R Dly[ms]
R Pre Delay
[ms]
0.0...50.0
Sets the delay time
for the right channel
p.253
Feedback ← –100...+100
Sets the feedback
amount p.255
HiDamp [%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range
Wet/Dry ←
–Wet...
–99 : 1, Dry,
99 : 1...Wet
Sets the balance
between the effect
and the dry input
p.226
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Chorus/Flanger
Left
Right
Feedback
180 [degree]
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
LFO1: Tri / Sine
LFO2: Tri / Sine
Chorus/Flanger
High Damp
To Next Page
Loading...
Need help?
General
