Korg KROSS - MIX (Mixer)

Program mode
58
15–5: MIX (Mixer)
Program [000...040]
Here you can select the program that will be used by the step
sequencer.
Note: Only drum programs can be selected.
If data is loaded or a system exclusive message is received so
that the selected program is no longer a Drum category
program, it will be replaced with the first program of the
Drum category.
The step sequencer program will not transmit or receive
MIDI program changes.
Play/Mute [Play, Mute]
This mutes the drum program. The setting will alternate each time
you press the Play/Mute button.
Play: Play: The drum program will be heard.
Mute: The drum program will not be heard (Mute).
Volume [000...127]
This adjusts the volume of the drum program.
Detune [–1200...+1200]
This adjusts the pitch in one-cent steps. One cent is 1/100th of a
semitone.
The pitch of each drum kit is specified in Global DRUM KIT.
FX Ctrl Bus (FX Control Bus) [Off, FC1, FC2]
This sends the output of the drum program to the FX Control bus
(two mono channels FX Ctrl1, 2).
The FX Control bus is used when you want to use another audio
signal to control the input of an effect. You can use the two FX
Control buses (two mono channels) to freely control the effects in
a variety of ways. For more information, please see the “FX
Control Bus” section on page 209.
Bus Select [Dkit, L/R, IFX1...5, Off]
This specifies the bus that will output the drum program.
Dkit: The Bus Select, FX Control Bus, MFX Send1, and MFX
Send 2 settings (Global DRUM KIT> VOICE page) for each key
of the drum kit used by the selected drum program will be valid.
Choose this setting if you want to apply separate insert effects to
each drum instrument.
Note: When making Dkit settings, you will normally use Dkit IFX
Patch to specify the output destination.
L/R: Output to the L/R bus.
IFX1, 2, 3, 4, 5: Output to the IFX1–5 bus.
Off: The sound will not be output to the L/R bus, or IFX1–5 bus.
Use the Off setting if you have connected the drum program output
in series to a master effect. Use Send1 (to MFX1) or Send2 (to
MFX2) to adjust the send level.
1 (MFX Send 1) [000...127]
2 (MFX Send 2) [000...127]
These specify the send level where the output of the drum program
will be sent to each master effect.
Send 1: Send the signal to master effect 1.
Send 2: Send the signal to master effect 2.
If Bus Select is set to IFX1–5, the send levels to the master effects
are set by the post-IFX1–5 Send1 and Send2 (P–FX ROUTING>
MIXER).
You can use CC#93 to control MFX Send 1, and CC#91 to
control MFX Send 2.
DKit IFX Patch
IFX1 [L/R, IFX1...5, Off]
IFX2 [L/R, IFX1...5, Off]
IFX3 [L/R, IFX1...5, Off]
IFX4 [L/R, IFX1...5, Off]
IFX5 [L/R, IFX1...5, Off]
Here you can patch the Bus Select setting specified for each key of
the drum kit, temporarily changing its connection destination from
the originally specified insert effect to some other destination. This
can be executed only if the drum track program’s Bus Select is set
to DKit and the Bus Select (Global DRUM KIT> VOICE page)
for each key of the drum kit is set to IFX1–5.
As the patch destination, choose an insert effect or L/R, IFX1–5,
or Off as the output bus.
Note: If you want to return the drum kit to its previous state,
change these settings to IFX1→IFX1, IFX2→IFX2, IFX3→IFX3,
IFX4→IFX4, and IFX5→IFX5.
For the preloaded kits, snare sounds are normally sent to IFX1,
kick sounds to IFX2, and symbal sounds to IFX3, toms, pucussion,
and other sounds to IFX4. In such cases if you set Bus Select to
Dkit, these sounds will be sent to IFX1, IFX2, IFX3 and IFX4, but
IFX1 and IFX2 are set for normal (non-drum) programs. In such
cases, you can use Dkit IFX Patch to route these drum sounds to
unused IFX; for example, you might send the snare sounds to
IFX3, kick sounds to IFX4, and other sounds to IFX5. For more
information, please see the “Effect Guide” section on page 207.
V 15–1...5: FUNCTION
•0: Write Program, Write/Initialize Program see page 63
•1: Solo Setting see page 63
•2: Compare see page 64
•3: Auto Song Setup see page 64
•4: Add to Favorite see page 64
•5: Assign inst to Tone see page 65
•6: Edits Step Parameters see page 65
•7: Copy Step Seq see page 65
For more information, please see the “Program: Function” section
on page 63.