Foot Switch Assign Dynamic Modulation Source List
301
Foot Switch Assign
Here you can assign the function of an assignable switch (a
separately sold PS-1 or PS-3) that's connected to the
ASSIGNABLE SWITCH jack.
• Create this setting in Global/Media mode G-INPUT/CTRL,
FOOT Foot SW Assign (see page 165).
If you choose a function that includes a CC#, that MIDI
control change message will be transmitted each time you
turn the switch on/off. (Off: 0, On: 127)
If you choose SW1 or 2, the MIDI control change message
specified by the Panel Switch Assign setting in each mode
will be transmitted each time you turn the switch on/off. (Off:
0, On: 127)
Foot Switch Assign List
Portamento SW (CC#65)
If Oscillator Mode (see page 7) is Single, turning the switch on
will apply portamento regardless of the Enable (see page 17)
setting; portamento will not apply when the switch is off.
If Oscillator Mode is Double, and the Enable setting is the same
for both oscillators 1 and 2 (i.e., enabled or disabled for both
oscillators 1 and 2), turning the switch on will apply portamento to
oscillators 1 and 2; portamento will not apply to oscillators 1 and 2
when the switch is off.
If the Enable setting differs between OSC1 and 2 (i.e., if oscillator
1 is enabled and oscillator 2 disabled, or if oscillator 1 is disabled
and oscillator 2 is enabled), then turning the switch on will apply
portamento to the oscillator that is enabled; portamento will not
apply to the oscillator when the switch is off.
Off The connected foot switch will have
no function.
Foot Switch
(CC#82)
Controls AMS or Dmod. To use this,
choose Foot SW:#82 for AMS, or
Foot #82 as the Dmod Src.
Portamento SW
(CC#65)
Turns portamento on/off.
Sostenuto (CC#66) Controls the sostenuto effect (only
the keys (note numbers) being
pressed when you turn the pedal
switch on will be held).
Soft (CC#67) Turns the soft pedal effect on/off.
Damper (CC#64) Turns the damper pedal effect on/off.
Program Up Selects a program or combination. If
the MAIN page of any mode is
displayed, the next-numbered sound
will be selected.
In Favorites mode, the next-
numbered favorite will be selected.
A bank select message and program
change message will also be
transmitted at this time.
Program Down Selects a program or combination. If
the MAIN page of any mode is
displayed, the next-numbered sound
will be selected.
In Favorites mode, the next-
numbered favorite will be selected.
A bank select message and program
change message will also be
transmitted at this time.
Value Inc Performs the same operation as
turning the VALUE dial toward the
right. (“Using a foot switch to select
Programs” on page 24 of the
Operation Guide)
Value Dec Performs the same operation as
turning the VALUE dial toward the
left.
Song Start/Stop Starts/stops the sequencer. A MIDI
start or stop message will also be
transmitted at this time.
Song Punch In/Out The switch will control sequencer
punch-in/punch-out in the Sequencer
mode SEQ, REC page when
“Recording Setup” is Manual Punch
In.
Audio Recorder
Start/Pause
Plays/pauses the audio recorder.
Audio Recorder
REC Start/Stop
Starts/stops recording on the audio
recorder.
Tap Tempo Controls the tempo of the arpeggiator
and song in real time.
ARP ON/OFF Turns the arpeggiator on/off.
DRUM TRACK
ON/OFF
Turns the Drum Track on/off.
STEP SEQ RUN Plays/stops the step sequencer.
Mod Wheel
(CC#01)
Controls the pitch bend wheel effect.
CC#02 (JS-Y) Controls AMS or Dmod. Choose
“JS-Y:#02” for AMS, or “JS-Y #2”
for Dmod Src.
CC#16 (Ribbon) Controls AMS or Dmod. To use this,
choose “Ribbon #16” for AMS, or
“Ribbn#16” as the Dmod Src.
SW1, SW2 Switch operations will control the
effect of the [SW1] or [SW2]
switches.
To Next Page
Loading...
