Effect Guide
266
High Damp [%]
Low Damp [%]
These parameters set the damping amount of high range and low
range. The tone of the delayed sound becomes darker and lighter
as it feeds back.
Spread
This parameter sets the pan width of the effect sound. The stereo
image is widest with a value of 50, and the effect sound of both
channels is output from the center with a value of 0.
090: Stereo/CrossDelay
This is a stereo delay, and can by used as a cross-feedback delay
effect in which the delay sounds cross over between the left and
right by changing the feedback routing.
091: St. Multitap Delay (Stereo
Multitap Delay)
The left and right Multitap Delays have two taps respectively.
Changing the routing of feedback and tap output allows you to
create various patterns of complex effect sounds.
Mode
You can change how the left and right delay signals are panned by
modifying the routing of the left and right delay as shown in the
figure above. You need to input different sounds to each channel in
order for this parameter to be effective.
Paramter Value Explanation
Mode ← Stereo, Cross
Switches between
stereo delay and
cross-feedback delay
L Dl[ms] L Delay [ms] 0.0...274.0
Sets the delay time
for the left channel
R DL[ms] R Delay [ms] 0.0...274.0
Sets the delay time
for the right channel
L Feedbck L Feedback –100...+100
Sets the feedback
amount for the left
channel
Src Source Off...Tempo
Selects the
modulation source of
feedback amount
Amt Amount –100...+100
Sets the modulation
amount of the left
channel feedback
R Feedbck R Feedback –100...+100
Sets the feedback
amount for the right
channel
Amt Amount –100...+100
Sets the modulation
amount of the right
channel feedback
HiDamp[%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range p.266
LoDamp[%]
Low Damp
[%]
0...100
Sets the damping
amount in the low
range p.266
InLvl Dmod
Input Level
Dmod [%]
–100...+100
Sets the modulation
amount of the input
level p.261
Src Source Off...Tempo
Selects the
modulation source
for the input level
p.261
Spread ← –50...+50
Sets the width of the
stereo image of the
effect sound p.266
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Delay
Delay
Stereo/Cross
Left
Right
Feedback
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp Low Damp
High Damp
Low Damp
Spread
Stereo/Cross
Paramter Value Explanation
Mode ←
Normal,
Cross
Feedback,
Cross Pan1,
Cross Pan2
Switches the left and
right delay routing
p.267
Hi Damp[%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range p.266
Lo Damp[%]
Low Damp
[%]
0...100
Sets the damping
amount in the low
range p.266
Tap1[ms]
Tap1
Time [ms]
0.0...274.0
Sets the Tap1 delay
time
Tap1 Level Level 0...100
Sets the Tap1 output
level p.267
Tap2[ms]
Tap2
Time [ms]
0.0...274.0
Sets the Tap2 delay
time
Fback(T2)
Tap2
Feedback
–100...+100
Sets the Tap2
feedback amount
Src Source Off...Tempo
Selects the
modulation source of
the Tap2 feedback
amount
Amt Amount –100...+100
Sets the modulation
amount of the Tap2
feedback amount
InLvl Dmod
Input Level
Dmod [%]
–100...+100
Sets the modulation
amount of the input
level p.261
Src Source Off...Tempo
Selects the
modulation source
for the input level
p.261
Spread ← –100...+100
Sets the width of the
stereo image of the
effect sound
p.266
Src Source Off...Tempo
Selects the
modulation source of
the effect sound’s
stereo image width
Amt Amount –100...+100
Sets the modulation
amount of the effect
sound’s stereo image
width
Wet/Dry ←
–Wet...
–99 : 1, Dry,
99 : 1...Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp
Low Damp
High Damp
Low Damp
Delay
Delay
Feedback
Tap1 Level
Mode
Mode
(1)
(2)
(1)
(2)
Tap1=(1)
Tap2=(2)
Mode: Normal Mode: Cross Feedback Mode: Cross Pan1 Mode: Cross Pan2
To Next Page
Loading...
