Single size effects 107: Reverb Room
277
107: Reverb Room
This room-type reverb emphasizes the early reflections that make
the sound tighter. Changing the balance between the early
reflections and reverb sound allows you to simulate nuances, such
as the type of walls of a room.
108: ReverbBrightRoom
This room-type reverb emphasizes the early reflections that make
the sound brighter.
Pre Delay
Pre Delay Thru [%]
“Pre Delay” specifies the delay time for the sound that is input to
the reverb. This controls the spaciousness.
“Pre Delay Thru” lets you accentuate the attack by mixing in
sound that does not pass through this delay.
ER Level
Reverb Level
These parameters set the early reflection level and reverb level.
Changing these parameter values will allow you to simulate the
type of walls in the room. That is, a larger “ER Level” simulates a
hard wall, and a larger “Reverb Level” simulates a soft wall.
109: Reverb2 Spring
The R2-type reverbs R2.Spring–R2.Room have a different sonic
character than Rev.Hall–Rev.Room2. They model the spring
reverb systems that are built into some amps.
110: Reverb2 Hall
This models the reverberation of a concert hall that includes
numerous echo components.
111: Reverb2 Plate
This models a type of reverb unit that vibrates a metal plate rather
than springs. The reverb time is relatively short. Because the
reverberation has a fast attack, it is suitable for percussive playing.
112: Reverb2 Room
This models the reverberation of a typical room that includes
numerous early reflections.
Time
In these reverbs, “Time” is not expressed in seconds, but instead is
a value from 1 to 100. A value of 1 produces the shortest reverb,
and 100 provides the longest reverb.
Paramter Value Explanation
Times [s]
Reverb Time
[sec]
0.1...3.0
Sets the reverber-
ation time
HiDamp[%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range
PreDl[ms]
Pre Delay
[msec]
0...200
Sets the delay time
from the dry sound
p.277
preDlyThru
Pre Delay
Thru [%]
0...100
Sets the mix ratio of
non-delay sound
p.277
ER Level ← 0...100
Sets the level of early
reflections p.277
Rev. Level Reverb Level 0...100
Sets the reverber-
ation level p.277
PreEQ Trim Pre EQ Trim 0...100
Sets the EQ input
level
Pre LEQ Fc
Low EQ
Frequency
Low,
Mid-Low
Selects the cutoff
frequency (low or
mid-low) of the low-
range equalizer
Pre HEQ Fc
High EQ
Frequency
High,
Mid-High
Selects the cutoff
frequency (high or
mid-high) of the
high-range equalizer
LEQ [dB]
Low EQ Gain
[dB]
–15.0...+15.0
Sets the gain of Low
EQ
HEQ [dB]
High EQ
Gain [dB]
–15.0...+15.0
Sets the gain of High
EQ
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
EQ Trim
+
EQ Trim
LEQ HEQ
Pre Delay
Reverb
Reverb Level
ER Level
ER Level
Pre Delay Thru
ERs
ERs
Paramter Value Explanation
Time [s] ← 0...100
Sets the reverber-
ation time p.278
HiDamp[%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range
LoDamp[%]
Low Damp
[%]
0...100
Sets the damping
amount in the low
range
PreDly [ms]
Pre Delay
[msec]
0...200
Sets the delay time
from the dry sound
p.278
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Reverb - Room Type
Time
Level
Louder
ER
(Early Reflections)
Dry
Reverb
Pre Delay Thru
Pre Delay
Reverb Time
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Pre Delay
Reverb
To Next Page
Loading...
