Double Size effects D12: St. Pitch Shifter (Stereo Pitch Shifter)
289
D12: St. Pitch Shifter (Stereo Pitch
Shifter)
This is a stereo pitch shifter. The pitch shift amount for the left and
right channels can be reversed from each other.
You can choose from three types: a type with rapid response, a
type with minimal tonal change and a type between these two.
L/R Pitch
When you select Up/Down for this parameter, the pitch shift
amount for the right channel will be reversed. If the pitch shift
amount is positive, the pitch of the left channel is raised, and the
pitch of the right channel is lowered.
Mode
Switches the operating mode of the pitch shifter. Slow minimizes
the tonal change, and Fast provides fast response. Med. is between
these two choices. Choose the Fast mode if you need only a small
amount of pitch shift, and choose Slow if you need a large amount
of pitch shift.
D13: Early Reflections
This early reflection effect has more precise early reflections with
twice the maximum length of a normal-size effect (See “113: Early
Reflections” on page 278.). You can create a very smooth and
dense sound.
Paramter Value Explanation
Mode
←
Slow, Med.,
Fast
Switches Pitch Shifter
mode
p.252
L/R Pitch
←
Normal,
Up/Down
Determines whether
or not the L/R pitch
shift amount is
inverted p.289
Pitch Shift
Shift
[1/2tone]
–24...+24
Sets the pitch shift
amount in steps of a
semitone p.261
Src Source Off...Tempo
Selects the
modulation source of
pitch shift amount
p.261
Amt Amount –24...+24
Sets the modulation
amount of pitch shift
amount p.261
Fine [c] Fine [cents] –100...+100
Sets the pitch shift
amount in steps of
one cent p.261
Amt Amount –100...+100
Sets the modulation
amount of pitch shift
amount p.261
L Dly[ms]
L Delay Time
[ms]
0...160
Sets the delay time
for the left channel
R Dly[ms]
R Delay Time
[ms]
0...160
Sets the delay time
for the right channel
Spread ← –100...+100
Sets the width of the
stereo image of the
effect sound
p.266
FB Posit
Feedback
Position
Pre, Post
Switches the
feedback connection
p.261
Feedback ← –100...+100
Sets the feedback
amount
p.261
HiDamp [%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range
InLvl Dmod
Input Level
Dmod [%]
–100...+100
Sets the modulation
amount of the input
level p.261
Src Source Off...Tempo
Selects the
modulation source
for the input level
p.261
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
High Damp
High Damp
Input Level
Input Level
Feedback Position
Pre
Pre
Post
Post
Delay
Pitch Shifter
Delay
Pitch Shifter
Paramter Value Explanation
Type ←
Sharp, Loose,
Modulated,
Reverse
Selects the decay
curve for the early
reflection p.278
Time [ms] ER Time [ms] 10...540
Sets the time length
of early reflection
PreDl[ms]
Pre Delay
[ms]
0...200
Sets the time taken
from the original
sound to the first
early reflection
PreEQ Trim Pre EQ Trim 0...100
Sets the input level of
EQ applied to the
effect sound
Pre LEQ Fc
Low EQ
Frequency
Low,
Mid-Low
Selects the cutoff
frequency (low or
mid-low) of the low-
range equalizer
Pre HEQ Fc
High EQ
Frequency
High,
Mid-High
Selects the cutoff
frequency (high or
mid-high) of the
high-range equalizer
LEQ [dB]
Low EQ Gain
[dB]
–15.0...+15.0
Sets the gain of Low
EQ
HEQ [dB]
High EQ
Gain [dB]
–15.0...+15.0
Sets the gain of High
EQ
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
EQ Trim
+
EQ Trim
Pre Delay
Early Reflections
LEQ HEQ
To Next Page
Loading...
Need help?
General
