Single size effects 036: 2Voice Resonator
237
036: 2Voice Resonator
This effect resonates the input signal at a specified pitch. You can
set the pitch, output level, and pan settings for two resonators
individually. You can control the resonance intensity via an LFO.
Control Mode
Voice 1 Resonance
Voice 2 Resonance
This parameter determines the resonance intensity.
When “Control Mode” = Manual, the “Resonance” parameter sets
the intensity of resonance. If the “Resonance” parameter has a
negative value, harmonics will be changed, and resonance will
occur at a pitch one octave lower.
When “Control Mode” = LFO, the intensity of resonance varies
according to the LFO. The LFO sways between positive and
negative values, causing resonance to occur between specified
pitches an octave apart in turn.
When “Control Mode” = Dmod, the resonance is controlled by the
dynamic modulation source. If P.Bend is assigned as the
modulation source, the pitch an octave higher and lower can be
controlled, similar to when LFO is selected for Control Mode.
LFO/Dmod Invert
When “Control Mode” = LFO or Dmod, the controlled phase of
either Voice 1 or 2 will be reversed. When the resonance pitch is
set for Voice 1 (Resonance has a positive value), Voice 2 will
resonate at a pitch an octave below (Resonance has a negative
value).
Voice 1 Pitch
Voice 1 Fine [cents]
Voice 2 Pitch
Voice 2 Fine [cents]
The Pitch parameter specifies the pitch of resonance by note name.
The “Fine” parameter allows for fine adjustment in steps of cents.
High Damp [%]
This sets the amount of damping amount for the high frequencies
of the resonant sound. Lower values create a metallic sound with a
higher range of harmonics.
Paramter Value Explanation
Control
Control
Mode
Manual, LFO,
Dmod
Switches the controls
of resonance intensity
p.237
Mod Invert
LFO/Dmod
Invert
Off, On
Reverses the Voice 1
and 2 control when
LFO/Dmod is selected
p.237
LFO [Hz]
LFO Freq
[Hz]
0.02...20.00
Sets the speed of the
LFO
Dmod Src
Dmod
Source
Off...Tempo
Selects the
modulation source
that controls
resonance intensity
MIDI Sync
BPM/MIDI
Sync
Off, On
When this is on, the
LFO speed is set by
BPM, Base Note, and
Times, instead of
Frequency p.223
BPM ←
MIDI,
40.00...
300.00
MIDI syncs to the
system tempo; 40–
300 sets the tempo
manually for this
individual effect p.223
Base Note ← ...
Selects the type of
notes that specify the
LFO speed p.223
Times ← x1...x32
Sets the number of
notes that specify the
LFO speed p.223
Mod. Depth ← –100...+100
Sets the amount of
resonance intensity
control via LFO/
Dmod
Trim ← 0...100
Sets the input level at
the resonator
V1 Pitch
Voice1
Pitch
C0...B8
Sets the voice1 Pitch
for resonance p.237
Fine [c]
Voice1
Fine [cents]
–50...+50
Fine-adjusts the voice
1 pitch for resonance
p.237
Lvl Level 0...100
Sets the Voice1
output level
V1 Reso
Voice1
Resonance
–100...+100
Sets the intensity of
resonance when
Control Mode =
Manual p.237
HDamp[%]
High Damp
[%]
0...100
Sets the damping
amount of resonant
sound in the high
range
p.237
Pan ←
L6...L1, C,
R1...R6
Sets the Voice1 stereo
image
V2 Pitch
Voice2
Pitch
C0...B8
Sets the voice 2 Pitch
for resonance p.237
Fine [c] Fine [cents] –50...+50
Fine-adjusts the voice
2 pitch for resonance
p.237
Lvl Level 0...100
Sets the Voice2
output level
V2 Reso
Voice2
Resonance
–100...+100
Sets the intensity of
resonance when
Control Mode =
Manual p.237
Left
Right
Resonance
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
High Damp
High Damp
Trim
Trim
+
Level
Level
Pan
Pan
Control Mode
D
-mod
LFO
Manual
Invert: On/Off
Resonator
Resonator
Pitch, Fine [cents]
HDamp[%]
High Damp
[%]
0...100
Sets the damping
amount of resonant
sound in the high
range p.237
Pan ←
L6...L1, C,
R1...R6
Sets the Voice2 stereo
image
Wet/Dry ←
Dry, 1 :99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
To Next Page
Loading...
